M28R400CT-KGD datasheet(3/11 Pages) STMICROELECTRONICS

3 / 11 page

3/11

M28R400CT-KGD, M28R400CB-KGD

SUMMARY DESCRIPTION

The M28R400C are available as Known Good

Dice.

STMicroelectronics defines Known Good Dice as

standard products offered as dice and tested for

functionality and speed. ST's Known Good Die

products are as reliable and of the same quality as

products delivered in packages.

This datasheet should be read in conjunction with

the full M28R400C datasheet.

The M28R400C is a 4 Mbit (256Kbit x 16) non-vol-

atile Flash memory that can be erased electrically

at the block level and programmed in-system on a

Word-by-Word basis. These operations can be

performed using a single low voltage (1.65 to

2.2V) supply. VDDQ allows to drive the I/O pin

down to 1.65V. An optional 12V VPP power supply

is provided to speed up customer programming.

The device features an asymmetrical blocked ar-

chitecture. The M28R400C has an array of 15

blocks: 8 Parameter Blocks of 4 KWord and 7

Main Blocks of 32 KWord. M28R400CT has the

Parameter Blocks at the top of the memory ad-

dress space while the M28R400CB locates the

Parameter Blocks starting from the bottom.

The M28R400C features an instant, individual

block locking scheme that allows any block to be

locked or unlocked with no latency, enabling in-

stant code and data protection. All blocks have

three levels of protection. They can be locked and

locked-down individually preventing any acciden-

tal programming or erasure. There is an additional

hardware protection against program and block

erase. When VPP ≤VPPLK all blocks are protected

against program or block erase. All blocks are

locked at power-up.

Each block can be erased separately. Erase can

be suspended in order to perform either read or

program in any other block and then resumed.

Program can be suspended to read data in any

other block and then resumed. Each block can be

programmed and erased over 100,000 cycles.

The device includes a 128 bit Protection Register

and a Security Block to increase the protection of

a system design. The Protection Register is divid-

ed into two 64 bit segments, the first one contains

a unique device number written by ST, while the

second one is one-time-programmable by the us-

er. The user programmable segment can be per-

manently

protected.

The

Security

Block,

parameter block 0, can be permanently protected

by the user.

Program and Erase commands are written to the

Command Interface of the memory. An on-chip

Program/Erase Controller takes care of the tim-

ings necessary for program and erase operations.

The end of a program or erase operation can be

detected and any error conditions identified. The

command set required to control the memory is

consistent with JEDEC standards.

The M28R400C are supplied with all the bits

erased (set to ‘1’)

Figure 2. Logic Diagram

Table 1. Signal Names

A0-A17

Address Inputs

DQ0-DQ15

Data Input/Output

Chip Enable

Output Enable

Write Enable

Reset

Write Protect

VDD

Core Power Supply

VDDQ

Power Supply for

Input/Output

VPP

Optional Supply Voltage for

Fast Program & Erase

VSS

Ground

AI04392

A0-A17

DQ0-DQ15

VDD

M28R400CT

M28R400CB

VSS

VDDQ VPP

M28R400CT-KGD датащи(PDF) 3 Page - STMicroelectronics

M28R400CT-KGD датащи(HTML) 3 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11

датащи скачать

ссылки URL