STM32F469AE datasheet(44/220 Pages) STMICROELECTRONICS

44 / 220 page

Functional overview

STM32F469xx

44/220

DS11189 Rev 7

2.35

Universal serial bus on-the-go full-speed (OTG_FS)

The device embeds an USB OTG full-speed device/host/OTG peripheral with integrated

transceivers. The USB OTG FS peripheral is compliant with the USB 2.0 specification and

with the OTG 2.0 specification. It has software-configurable endpoint setting and supports

suspend/resume. The USB OTG controller requires a dedicated 48 MHz clock that is

generated by a PLL connected to the HSE oscillator.

The main features are:



Combined Rx and Tx FIFO size of 1.28 KB with dynamic FIFO sizing



Supports the session request protocol (SRP) and host negotiation protocol (HNP)



1 bidirectional control endpoint + 5 IN endpoints + 5 OUT endpoints



12 host channels with periodic OUT support



Software configurable to OTG1.3 and OTG2.0 modes of operation



USB 2.0 LPM (Link Power Management) support



Internal FS OTG PHY support



HNP/SNP/IP inside (no need for any external resistor)

For OTG/Host modes, a power switch is needed in case bus-powered devices are

connected

2.36

Universal serial bus on-the-go high-speed (OTG_HS)

The device embeds a USB OTG high-speed (up to 480 Mb/s) device/host/OTG peripheral.

The USB OTG HS supports both full-speed and high-speed operations. It integrates the

transceivers for full-speed operation (12 MB/s) and features a UTMI low-pin interface (ULPI)

for high-speed operation (480 MB/s). When using the USB OTG HS in HS mode, an

external PHY device connected to the ULPI is required.

The USB OTG HS peripheral is compliant with the USB 2.0 specification and with the OTG

2.0 specification. It has software-configurable endpoint setting and supports

suspend/resume. The USB OTG controller requires a dedicated 48 MHz clock that is

generated by a PLL connected to the HSE oscillator.

The main features are:



Combined Rx and Tx FIFO size of 4 KB with dynamic FIFO sizing



Supports the session request protocol (SRP) and host negotiation protocol (HNP)



8 bidirectional endpoints



16 host channels with periodic OUT support



Software configurable to OTG1.3 and OTG2.0 modes of operation



USB 2.0 LPM (Link Power Management) support



Internal FS OTG PHY support



External HS or HS OTG operation supporting ULPI in SDR mode. The OTG PHY is

connected to the microcontroller ULPI port through 12 signals. It can be clocked using

the 60 MHz output.



Internal USB DMA



HNP/SNP/IP inside (no need for any external resistor)



for OTG/Host modes, a power switch is needed in case bus-powered devices are

connected

STM32F469AE датащи(PDF) 44 Page - STMicroelectronics

STM32F469AE датащи(HTML) 44 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL