SH7041A datasheet(268/923 Pages) RENESAS

268 / 923 page

230

11.3.2

DMA Transfer Requests

DMA transfer requests are usually generated in either the data transfer source or destination, but

they can also be generated by devices and on-chip peripheral modules that are neither the source

nor the destination. Transfers can be requested in three modes: auto-request, external request, and

on-chip peripheral module request. The request mode is selected in the RS3–RS0 bits of the DMA

channel control registers 0–3 (CHCR0–CHCR3).

Auto-Request Mode: When there is no transfer request signal from an external source, as in a

memory-to-memory transfer or a transfer between memory and an on-chip peripheral module

unable to request a transfer, the auto-request mode allows the DMAC to automatically generate a

transfer request signal internally. When the DE bits of CHCR0–CHCR3 and the DME bit of the

DMAOR are set to 1, the transfer begins (so long as the TE bits of CHCR0–CHCR3 and the

NMIF and AE bits of DMAOR are all 0).

External Request Mode: In this mode a transfer is performed at the request signal (

DREQ) of an

external device. Choose one of the modes shown in table 11.3 according to the application system.

When this mode is selected, if the DMA transfer is enabled (DE = 1, DME = 1, TE = 0, NMIF = 0,

AE = 0), a transfer is performed upon a request at the

DREQ input. Choose to detect DREQ by

either the falling edge or low level of the signal input with the DS bit of CHCR0–CHCR3 (DS = 0

is level detection, DS = 1 is edge detection). The source of the transfer request does not have to be

the data transfer source or destination.

Table 11.3

Selecting External Request Modes with the RS Bits

RS3

RS2

RS1

RS0

Address Mode

Source

Destination

0000

Dual address

mode

Any*

0010

Single address

mode

External memory or

memory-mapped

external device

External device with

DACK

0011

Single address

mode

External device with

DACK

External memory or

memory-mapped

external device

Note: * External memory, memory-mapped external device, on-chip memory, on-chip peripheral

module (excluding DMAC, DTC, BSC, UBC).

On-Chip Peripheral Module Request Mode: In this mode a transfer is performed at the transfer

request signal (interrupt request signal) of an on-chip peripheral module. As indicated in table

11.4, there are ten transfer request signals: five from the multifunction timer pulse unit (MTU),

which are compare match or input capture interrupts; the receive data full interrupts (RxI) and

transmit data empty interrupts (TxI) of the two serial communication interfaces (SCI); and the A/D

conversion end interrupt (ADI1 for A mask, ADI for others) of the A/D converter. When DMA

SH7041A датащи(PDF) 268 Page - Renesas Technology Corp

SH7041A датащи(HTML) 268 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL