AGLP030 datasheet(16/128 Pages) ACTEL

16 / 128 page

IGLOO PLUS DC and Switching Characteristics

2- 2

R ev isio n 1 1

Table 2-2 • Recommended Operating Conditions1,2

Symbol

Parameter

Commercial

Industrial

Units

Ambient temperature

0 to +70

–40 to +85

°C

Junction temperature2

0 to + 85

–40 to +100

°C

VCC3

1.5 V DC core supply voltage 4

1.425 to 1.575

1.2 V–1.5 V wide range core voltage5,6

1.14 to 1.575

VJTAG

JTAG DC voltage

1.4 to 3.6

VPUMP7

Programming voltage

Programming mode

3.15 to 3.45

Operation

0 to 3.6

VCCPLL8

Analog power supply (PLL)

1.5 V DC core supply voltage4

1.425 to 1.575

1.2 V–1.5 V wide range core

voltage5

1.14 to 1.575

VCCI

1.2 V DC supply voltage5

1.14 to 1.26

1.2 V DC wide range supply voltage5

1.14 to 1.575

1.5 V DC supply voltage

1.425 to 1.575

1.8 V DC supply voltage

1.7 to 1.9

2.5 V DC supply voltage

2.3 to 2.7

3.3 V wide range DC supply voltage9

2.7 to 3.6

3.3 V DC supply voltage

3.0 to 3.6

Notes:

1. All parameters representing voltages are measured with respect to GND unless otherwise specified.

2. To ensure targeted reliability standards are met across ambient and junction operating temperatures, Actel recommends

that the user follow best design practices using Actel’s timing and power simulation tools.

3. The ranges given here are for power supplies only. The recommended input voltage ranges specific to each I/O

standard are given in Table 2-21 on page 2-19. VCCI should be at the same voltage within a given I/O bank.

4. For IGLOO® PLUS V5 devices

5. For IGLOO PLUS V2 devices only, operating at VCCI

≥ VCC.

6. All IGLOO PLUS devices (V5 and V2) must be programmed with the VCC core voltage at 1.5 V. Applications using V2

devices powered by a 1.2 V supply must switch the core supply to 1.5 V for in-system programming.

7. VPUMP can be left floating during operation (not programming mode).

8. VCCPLL pins should be tied to VCC pins. See the Pin Descriptions chapter of the IGLOO PLUS FPGA Fabric User’s

Guide for further information.

9. 3.3 V wide range is compliant to the JDEC8b specification and supports 3.0 V VCCI operation.

Table 2-3 • Flash Programming Limits – Retention, Storage, and Operating Temperature 1

Product

Grade

Programming

Cycles

Program

Retention

(biased/unbiased)

Maximum Storage

Temperature TSTG

(°C) 2

Maximum Operating

Junction

Temperature TJ (°C)

Commercial

500

20 years

110

100

Industrial

500

20 years

110

100

Notes:

1. This is a stress rating only; functional operation at any condition other than those indicated is not implied.

2. These limits apply for program/data retention only. Refer to Table 2-1 on page 2-1 and Table 2-2 for device operating

conditions and absolute limits.

AGLP030 датащи(PDF) 16 Page - Actel Corporation

AGLP030 датащи(HTML) 16 Page - Actel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL