PIC12F635ESLASHSS datasheet(111/196 Pages) MICROCHIP

111 / 196 page

Preliminary

DS41232B-page 109

PIC12F635/PIC16F636/639

AFE STATUS REGISTER 7 (ADDRESS: 0111)

See Table 11-7 for the bit conditions of the AFE Status

Power-on Reset.

R-0

CHZACT

CHYACT

CHXACT

AGCACT

WAKEZ

WAKEY

WAKEX

ALARM

PEI

bit 8

bit 0

bit 8

CHZACT: Channel Z Active(1) bit (cleared via Soft Reset)

= Channel Z is passing data after TAGC

= Channel Z is not passing data after TAGC

bit 7

CHYACT: Channel Y Active(1) bit (cleared via Soft Reset)

= Channel Y is passing data after TAGC

= Channel Y is not passing data after TAGC

bit 6

CHXACT: Channel X Active(1) bit (cleared via Soft Reset)

= Channel X is passing data after TAGC

= Channel X is not passing data after TAGC

bit 5

AGCACT: AGC Active Status bit (real time, cleared via Soft Reset)

= AGC is active (Input signal is strong). AGC is active when input signal level is approximately >

20 mVPP range.

= AGC is inactive (Input signal is weak)

bit 4

WAKEZ: Wake-up Channel Z Indicator Status bit (cleared via Soft Reset)

= Channel Z caused a AFE wake-up (passed

÷64 clock counter)

= Channel Z did not cause a AFE wake-up

bit 3

WAKEY: Wake-up Channel Y Indicator Status bit (cleared via Soft Reset)

= Channel Y caused a AFE wake-up (passed

÷64 clock counter)

= Channel Y did not cause a AFE wake-up

bit 2

WAKEX: Wake-up Channel X Indicator Status bit (cleared via Soft Reset)

= Channel X caused a AFE wake-up (passed

÷64 clock counter)

= Channel X did not cause a AFE wake-up

bit 1

ALARM: Indicates whether an Alarm timer time-out has occurred (cleared via read “Status Register

command”)

= The Alarm timer time-out has occurred. It may cause the ALERT output to go low depending on the

state of bit 4 of the Configuration register 0

= The Alarm timer is not timed out

bit 0

PEI: Parity Error Indicator bit – indicates whether a Configuration register parity error has occurred (real

time)

= A parity error has occurred and caused the ALERT output to go low

= A parity error has not occurred

Note 1: Bit is high whenever channel is passing data. Bit is low in Standby mode.

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

- n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

PIC12F635E/SS датащи(PDF) 111 Page - Microchip Technology

PIC12F635E/SS датащи(HTML) 111 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL