CP5.241, CP5.241-C1, CP5.241-S1,

CP5.241-S2, CP5.242

CP-Series

Feb. 2018 / Rev. 0.3 DS-CP5.241-EN

All parameters are typical values specified at 230Vac, 50Hz input voltage, 24V, 5A output load,

25°C ambient and after a 5 minutes run-in time unless otherwise noted.

www.pulspower.com Phone +49 89 9278 0

Germany

15/28

P R E L I M I N A R Y

15. EMC

The EMC behavior of the device is designed for applications in industrial environment as well as in residential,

commercial and light industry environments.

EMC Immunity

According to the generic standards EN 61000-6-1 and EN 61000-6-2.

Electrostatic discharge

EN 61000-4-2

Contact discharge

Air discharge

8kV

15kV

Criterion A

Criterion A

Electromagnetic RF field

EN 61000-4-3

80MHz-2.7GHz

20V/m

Criterion A

Fast transients (Burst)

EN 61000-4-4

Input lines

Output lines

DC-OK signal (coupling clamp)

4kV

2kV

2kV

Criterion A

Criterion A

Criterion A

Surge voltage on input

EN 61000-4-5

L

N

L

PE, N

PE

2kV

4kV

Criterion A

Criterion A

Surge voltage on output

EN 61000-4-5

+

-

+ / -

PE

1kV

2kV

Criterion A

Criterion A

Surge voltage on DC-OK

EN 61000-4-5

DC-OK signal

PE

1kV

Criterion A

Conducted disturbance

EN 61000-4-6

0.15-80MHz

20V

Criterion A

Mains voltage dips

EN 61000-4-11

0% of 100Vac

40% of 100Vac

70% of 100Vac

0% of 200Vac

40% of 200Vac

70% of 200Vac

0Vac, 20ms

40Vac, 200ms

70Vac, 500ms

0Vac, 20ms

80Vac, 200ms

140Vac, 500ms

Criterion A

Criterion C

Criterion A

Criterion A

Criterion A <4A

Criterion C >4A

Criterion A

Voltage interruptions

EN 61000-4-11

0% of 200Vac (=0V)

5000ms

Criterion C

Voltage sags

SEMI F47 0706

Dips on the input voltage according to SEMI F47 standard

80% of 120Vac (96Vac)

70% of 120Vac (84Vac)

50% of 120Vac (60Vac)

1000ms

500ms

200ms

Criterion A

Criterion A

Criterion A

Powerful transients

VDE 0160

Over entire load range

750V, 0.3ms

Criterion A

Performance criterions:

A: Power supply shows normal operation behavior within the defined limits.

C: Temporary loss of function is possible. Device may shut-down and restarts by itself. No damage or hazards for the power supply will occur.

EMC Emission

According to the generic standards EN 61000-6-3 and EN 61000-6-4.

Conducted emission

input lines

EN 55011, EN 55022, FCC Part 15, CISPR 11, CISPR 22

Class B

Conducted emission

IEC/CISPR 16-1-2, IEC/CISPR 16-2-1

Class A for information only, not

mandatory for EN 61000-6-3

Radiated emission

EN 55011, EN 55022

Class B

Harmonic input current (PFC)

EN 61000-3-2

Class A equipment: fulfilled

Voltage fluctuations, flicker

EN 61000-3-3

current loads, non pulsing

This device complies with FCC Part 15 rules.

Operation is subjected to following two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause undesired operation.

Switching Frequencies

PFC converter

70kHz to 130kHz

Input voltage and output load dependent

Main converter

60kHz to 140kHz

Output load dependent

Auxiliary converter

60kHz

Fixed frequency