| поискавой системы для электроныых деталей |
|
SSD1850 датащи(PDF) 29 Page - List of Unclassifed Manufacturers |
|
|
|||||||||||||||||||||||||||||
SSD1850 датащи(HTML) 29 Page - List of Unclassifed Manufacturers |
|
29 / 56 page ![]() SSD1850/51 Series Rev 1.2 01/2003 SOLOMON 25 B0~BF 1 0 1 1 P3 P2 P1 P0 Set Page Address Set GDDRAM page address (0~10) using P3P2P1P0 for RAM access. The page address is sets to 0 after reset. C0~CF 1 1 0 0 S0 X X X Set COM Output Scan Direction S0=0: Normal mode (POR) S0=1: Remapped mode. COM0 to COM[N-1] becomes COM[N-1] to COM0 when the duty is set to N. See Figure 5 as an example for N equals to 80. *Note: This command will not affect the display of the icon lines D0~E0 Reserved Reserved E1 1 1 1 0 0 0 0 1 Exit Power-save Mode DC-DC converter, regulator and divider status before entering the power-save mode is restored. At POR, Power-save Mode is released. E2 1 1 1 0 0 0 1 0 Software Reset Initialize some internal registers E3 Reserved Reserved E4 1 1 1 0 0 1 0 0 Exit N-line Inversion The frame will be inverted once per frame E5~E7 Reserved Reserved E8 1 D7 1 D6 1 D5 0 D4 1 D3 0 D2 0 D1 0 D0 Set Display Data Length This command is valid only at 3-wire SPI (PS0=PS1=L) The next command specifies the number of bytes of display data to be written after this composite command. D(7:0)=00: 1 byte of display data is to be sent D(7:0)=FF: 256 bytes of display data is to be sent E9~EF Reserved Reserved F0~FF 1 1 1 1 X X X X Extended Features Test mode commands and Extended features, see Extended Command Table. Extended Command Table Bit Pattern Command Description 11110000 000000X1X0 X1X0 : Set VL6 noise reduction X1X0 = 00: Enable (POR) X1X0 = 11: Normal Remarks: This command is only valid for the IC version with G prefix notation on the “DTE” (datecode) field of label printed on die tray cover, intermediates and outer boxes. 11110001 00001X2X1X0 X2X1X0 : Set TC Value X2X1X0 = 000: -0.05%/ °C (POR) X2X1X0 = 001: -0.07%/ °C 11110111 0000000X0 Select Oscillator Source X0 = 0: Internal RC oscillator is selected (POR) X0 = 1: External oscillator from CL pin is selected 11110010 00000X2X1X0 Oscillator Adjustment X2X1X0 = 000: -9% X2X1X0 = 001: -6% X2X1X0 = 010: -3% X2X1X0 = 011: 0 (POR) X2X1X0 = 100: +3% |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |