AD5522JSVDZ datasheet(43/65 Pages) AD

43 / 65 page

AD5522

Data Sheet

Rev. E | Page 42 of 64

SERIAL INTERFACE

The AD5522 provides two high speed serial interfaces: an SPI-

compatible interface operating at clock frequencies up to 50 MHz

and an EIA-644-compliant LVDS interface. To minimize both

the power consumption of the device and the on-chip digital

noise, the serial interface powers up fully only when the device

is being written to, that is, on the falling edge of SYNC.

SPI INTERFACE

The serial interface operates from a 2.3 V to 5.25 V DVCC supply

range. The SPI interface is selected when the SPI/LVDS pin is

held low. It is controlled by four pins, as described in Table 15.

Table 15. Pins That Control the SPI Interface

Description

SYNC

Frame synchronization input

SDI

Serial data input pin

SCLK

Clocks data in and out of the device

SDO

Serial data output pin for data readback (weak

SDO output driver, may require reduction in SCLK

frequency to correctly read back, see Table 2)

LVDS INTERFACE

The LVDS interface uses the same input pins, with the same

designations, as the SPI interface. In addition, four other pins

are provided for the complementary signals needed for differ-

ential operation, as described in Table 16.

Table 16. Pins That Control the LVDS Interface

Description

SYNC

Differential frame synchronization signal

SYNC

Differential frame synchronization signal

(complement)

SDI

Differential serial data input

SDI

Differential serial data input (complement)

SCLK

Differential serial clock input

SCLK

Differential serial clock input (complement)

SDO

Differential serial data output for data readback

SDO

Differential serial data output for data readback

(complement)

SERIAL INTERFACE WRITE MODE

The AD5522 allows writing of data via the serial interface to

every register directly accessible to the serial interface, that is,

all registers except the DAC registers.

The serial word is 29 bits long. The serial interface works with

both a continuous and a burst (gated) serial clock. Serial data

applied to SDI is clocked into the AD5522 by clock pulses

applied to SCLK. The first falling edge of SYNC starts the write

cycle. At least 29 falling clock edges must be applied to SCLK to

clock in 29 bits of data before SYNC is taken high again.

The input register addressed is updated on the rising edge of

SYNC. For another serial transfer to take place, SYNC must be

taken low again.

The shift register can accept longer words (for example, 32-bit

words), framed by SYNC, but the data should always be in the

29th LSB positions.

RESET FUNCTION

Bringing the level-sensitive RESET line low resets the contents

of all internal registers to their power-on reset state (see the

Power-On Default section). This sequence takes approximately

600 µs. BUSY goes low for the duration, returning high when

RESET is brought high again and the initialization is complete.

While BUSY is low, all interfaces are disabled. When BUSY

returns high, normal operation resumes, and the status of the

RESET pin is ignored until it goes low again. The SDO output is

high impedance during a power-on reset or a RESET. A power-

on reset functions the same way as RESET.

BUSY AND LOAD FUNCTIONS

The BUSY pin is an open-drain output that indicates the status

of the AD5522 interface. When writing to any register, BUSY

goes low and stays low until the command completes.

A write operation to a DAC X1 register and some PMU register

bits (see Table 18) drives the BUSY signal low for longer than a

write M, C, or system control register. For DACs, the value of

the internal cached (X2) data is calculated and stored each time

that the user writes new data to the corresponding X1 register.

During the calculation and writing of X2, the BUSY output is

driven low. While BUSY is low, the user can continue writing

new data to the any register, but this write should not be

completed with SYNC going high until BUSY returns high (see

Figure 56 and Figure 57).

X2 values are stored and held until a PMU word is written that

calls the appropriate cached X2 register. Only then is a DAC

output updated.

The DAC outputs and PMU modes are updated by taking the

LOAD input low. If LOAD goes low while BUSY is active, the

LOAD event is stored and the DAC outputs or PMU modes are

updated immediately after BUSY goes high. A user can also hold

the LOAD input permanently low. In this case, the DAC outputs

or PMU modes are updated immediately after BUSY goes high.

The BUSY pin is bidirectional and has a 50 kΩ internal pull-up

resistor. When multiple AD5522 devices are used in one system,

the BUSY pins can be tied together. This is useful when it is

required that no DAC or PMU in any device be updated until

all others are ready to be updated. When each device finishes

updating its X2 registers, it releases the BUSY pin. If another

device has not finished updating its X2 registers, it holds BUSY

low, thus delaying the effect of LOAD going low.

AD5522JSVDZ датащи(PDF) 43 Page - Analog Devices

AD5522JSVDZ датащи(HTML) 43 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65

датащи скачать

ссылки URL