AD9601 datasheet(20/33 Pages) AD

20 / 33 page

AD9601

Rev. 0 | Page 19 of 32

TIMING—SINGLE PORT MODE

In single port mode, the CMOS output data is available from

Data Port A (DA0 to DA9). The outputs for Port B (DB0 to

DB9) are unused, and are high impedance in this mode.

The Port A outputs and the differential output data clock

(DCO+/DCO−) switch nearly simultaneously during the rising

edge of DCO+. In this mode, it is recommended to use the

rising edge of DCO− to capture the data from Port A. The setup

and hold time depends on the input sample clock period, and is

approximately 1/fCLK ± tSKEW.

TIMING—INTERLEAVED MODE

In interleaved mode, the output data of the AD9601 is de-

multiplexed onto two data port buses, Port A (DA0 to DA9) and

Port B (DB0 to DB9). The output data and differential data

capture clock switch at one-half the rate of the sample clock

input (CLK+/CLK−), increasing the setup and hold time for the

external data capture circuit relative to single port mode (see

Figure 3, interleaved mode timing diagram). The two ports

switch on alternating sample clock cycles, with the data for

Port A being valid during the rising edge of DCO+, and the

data for Port B being valid during the rising edge of DCO−. The

pipeline latency for both ports is six sample clock cycles. Due to

the random nature of the ÷2 circuit that generates the timing

for the output stage in interleaved mode, the first data sample

during power-up can be assigned to either Data Port A or Port

B. The user cannot control the polarity of the output data clock

relative to the input sample clock. In this mode, it is recom-

mended to use the rising edge of DCO+ to capture the data

from Port A, and the rising edge of DCO− to capture the data

from Port B. In both cases, the setup and hold time depends on

the input sample clock period, and both are approximately

2/fS ± tSKEW.

fS/2 Spurious

Because the AD9601 output data rate is at one-half the sampling

frequency in interleaved output mode, there is significant fS/2

energy in the outputs of the part, and there is significant energy

in the ADC output spectrum at fS/2. Care must be taken to be

certain that this fS/2 energy does not couple into either the clock

circuit or the analog inputs of the AD9601. When fS/2 energy is

coupled in this fashion, it appears as a spurious tone reflected

around fS/4, 3fS/4, 5fS/4, and so on. For example, in a 125 MSPS

sampling application with a 90 MHz single-tone analog input,

this energy generates a tone at 97.5 MHz.

[(3 × 125 MSPS/4 − 90 MHz) + 3 × 125 MSPS/4]

Depending on the relationship of the IF frequency to the center

of the Nyquist zone, this spurious tone may or may not be in the

user’s band of interest. Some residual fS/2 energy is present in

the AD9601, and the level of this spur is typically below the

level of the harmonics at clock rates. Figure 20 shows a plot of

the fS/2 spur level vs. the analog input frequency for the

AD9601-250. For the specifications provided in Table 2, the fS/2

spur effect is not a factor, as the device is specified in single port

output mode.

AD9601 датащи(PDF) 20 Page - Analog Devices

AD9601 датащи(HTML) 20 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

датащи скачать

ссылки URL