DM505LRBABFR datasheet(81/290 Pages) TI1

81 / 290 page

DM505

www.ti.com

SPRS976D – NOVEMBER 2016 – REVISED JULY 2017

Submit Documentation Feedback

Specifications

5.5

Operating Performance Points

This section describes the operating conditions of the device. This section also contains the description of

each OPP (operating performance point) for processor clocks and device core clocks.

Table 5-1 describes the maximum supported frequency per speed grade for the devices.

Table 5-1. Speed Grade Maximum Frequency

Device Speed

Maximum frequency (MHz)

DSP

EVE

IPU

ISS

DDR3/DDR3L

DDR2

LPDDR2

ADC

DM505xxR

745

667

212.8

266

532 (DDR-1066)

400 (DDR-800)

333 (DDR-667)

5.5.1

AVS Requirements

Adaptive Voltage Scaling (AVS) is required on most of the vdd_* supplies as defined in Table 5-2.

Table 5-2. AVS Requirements per vdd_* Supply

Supply

AVS Required?

vdd

Yes, for all OPPs

vdd_dspeve

Yes, for all OPPs

5.5.2

Voltage And Core Clock Specifications

Table 5-3 shows the recommended OPP per voltage domain.

Table 5-3. Voltage Domains Operating Performance Points

DOMAIN

CONDITION

OPP_NOM

OPP_OD

OPP_HIGH

MIN (2)

NOM (1)

MAX (2)

MIN (2)

NOM (1)

MAX (2)

MIN (2)

NOM (1)

MAX DC (3)

MAX (2)

VD_CORE (V)

BOOT (Before

AVS is enabled)

(4)

1.02

1.06

1.11

Not Applicable

After AVS is

enabled (4)

AVS

Voltage

(5) –

3.5%

AVS

Voltage

(5)

1.11

Not Applicable

VD_DSPEVE

(V)

BOOT (Before

AVS is enabled)

(4)

1.02

1.06

1.11

Not Applicable

After AVS is

enabled (4)

AVS

Voltage

(5) –

3.5%

AVS

Voltage

(5)

1.11

AVS

Voltage

(5) –

3.5%

AVS

Voltage

(5)

AVS

Voltage

(5) + 5%

AVS

Voltage

(5) –

3.5%

AVS

Voltage

(5)

AVS

Voltage (5)

+ 2%

AVS

Voltage

(5) + 5%

(1) In a typical implementation, the power supply should target the NOM voltage.

(2) The voltage at the device ball should never be below the MIN voltage or above the MAX voltage for any amount of time. This

requirement includes dynamic voltage events such as AC ripple, voltage transients, voltage dips, etc.

(3) The DC voltage at the device ball should never be above the MAX DC voltage to avoid impact on device reliability and lifetime POH

(Power-On-Hours). The MAX DC voltage is defined as the highest allowed DC regulated voltage, without transients, seen at the ball.

(4) For all OPPs, AVS must be enabled to avoid impact on device reliability, lifetime POH (Power-On-Hours), and device power.

(5) The AVS voltages are device-dependent, voltage domain-dependent, and OPP-dependent. They must be read from the

STD_FUSE_OPP. For information about STD_FUSE_OPP Registers address, please refer to Control Module Section of the TRM. The

power supply should be adjustable over the following ranges for each required OPP:

–

OPP_NOM: 0.85V - 1.06V

–

OPP_OD: 0.94V - 1.15V

–

OPP_HIGH: 1.05V - 1.25V

The AVS Voltages will be within the above specified ranges.

DM505LRBABFR датащи(PDF) 81 Page - Texas Instruments

DM505LRBABFR датащи(HTML) 81 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL