DLP2000 datasheet(37/40 Pages) TI1

37 / 40 page

SECTION A-A

NOTCH OFFSETS

DWG NO.

INV11-2006a

2510560

TITLE

SIZE

DWG NO

REV

SCALE

SHEET

DATE

ENGINEER

QA/CE

APPROVED

DRAWN

INSTRUMENTS

Dallas Texas

APPLICATION

NEXT ASSY

USED ON

THIRD ANGLE

PROJECTION

TEXAS

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN MILLIMETERS

TOLERANCES:

ANGLES

1

2 PLACE DECIMALS

0.25

1 PLACE DECIMALS

0.50

DIMENSIONAL LIMITS APPLY BEFORE PROCESSES

INTERPRET DIMENSIONS IN ACCORDANCE WITH ASME

Y14.5M-1994

REMOVE ALL BURRS AND SHARP EDGES

PARENTHETICAL INFORMATION FOR REFERENCE ONLY

ICD, MECHANICAL, DMD,

.2 nHD DDR SERIES 230

(FQC PACKAGE)

2510560

8/3/2009

25:1

P. KONRAD

F. ARMSTRONG

8/3/2009

NONE

0314DA

B. HASKETT

NOTES UNLESS OTHERWISE SPECIFIED:

REVISIONS

B. HASKETT

J. GRIMMETT

8/3/2009

REV

DESCRIPTION

DATE

ECO 2100735 INITIAL RELEASE

8/3/09

BMH

ECO 2102356 ADD DATUM E AND NOTE 9; UPDATE

SOLDER APPEARANCE; TIGHTEN NOTCH X-AXIS TOL'S

10/22/09

BMH

ECO 2104056 CHG ENCAP MAX HEIGHT FROM TBD TO ZERO

1/4/10

BMH

ECO 2166625 ADD "FQC PACKAGE" TO DRAWING TITLE;

SHOW APERTURE CORNER RADII PICTORIALLY

5/30/17

BMH

90°

1°

2.485 - 0.1

0.2

4.97 - 0.075

0.275

12.32

0.08

0.8 - 0.1

0.2

14.12 - 0.1

0.3

(1)

1.235 - 0.1

0.2

2.5

0.075

0.703

0.057

0.78

0.063

1.2

0.1

(1.483)

ACTIVE ARRAY

(PANASONIC AXT642124DD1, 42-CONTACT,

0.4 mm PITCH BOARD-TO-BOARD HEADER)

INTERFACE TO PANASONIC AXT542124DD1 SOCKET

3 SURFACES INDICATED

IN VIEW B (SHEET 2)

(ILLUMINATION

DIRECTION)

 0.05

0.038 A

 0.02D

DIE PARALLELISM TOLERANCE APPLIES TO DMD ACTIVE ARRAY ONLY.

ROTATION ANGLE OF DMD ACTIVE ARRAY IS A REFINEMENT OF THE LOCATION

TOLERANCE AND HAS A MAXIMUM ALLOWED VALUE OF 0.6 DEGREES.

BOUNDARY MIRRORS SURROUNDING THE DMD ACTIVE ARRAY.

DMD MARKING TO APPEAR IN CONNECTOR RECESS.

NOTCH DIMENSIONS ARE DEFINED BY UPPERMOST LAYERS OF CERAMIC,

AS SHOWN IN SECTION A-A.

ENCAPSULANT TO BE CONTAINED WITHIN DIMENSIONS SHOWN IN VIEW C

(SHEET 2). NO ENCAPSULANT IS ALLOWED ON TOP OF THE WINDOW.

ENCAPSULANT NOT TO EXCEED THE HEIGHT OF THE WINDOW.

DATUM B IS DEFINED BY A DIA. 2.5 PIN, WITH A FLAT ON THE SIDE FACING

TOWARD THE CENTER OF THE ACTIVE ARRAY, AS SHOWN IN VIEW B (SHEET 2).

WHILE ONLY THE THREE DATUM A TARGET AREAS A1, A2, AND A3 ARE USED

FOR MEASUREMENT, ALL 4 CORNERS SHOULD BE CONTACTED, INCLUDING E1,

TO SUPPORT MECHANICAL LOADS.

(SHEET 3)

0.2

0.05

0.4

0.1

0.35 MIN.

TYP.

0 MIN. TYP.

(

2.5)

1.176

0.05 5

(0.88)

0.4

0.03

(2.5) 5

2X ENCAPSULANT

DLP2000 датащи(PDF) 37 Page - Texas Instruments

DLP2000 датащи(HTML) 37 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

датащи скачать

ссылки URL