LT1794 datasheet(3/16 Pages) LINER

3 / 16 page

LT6301

sn6301 6301f

SYMBOL

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

ELECTRICAL CHARACTERISTICS

The q denotes the specifications which apply over the full specified temperature range, otherwise specifications are at TA = 25°C.

VCM = 0V, pulse tested, ±5V ≤ VS ≤ ±12V, VSHDNREF = 0V, RBIAS = 24.9k between V+ and SHDN unless otherwise noted. (Note 3)

PSRR

Power Supply Rejection Ratio

VS = ±4V to ±12V

AVOL

Large-Signal Voltage Gain

VS = ±12V, VOUT = ±10V, RL = 40Ω

VS = ±5V, VOUT = ±3V, RL = 25Ω

VOUT

Output Swing

VS = ±12V, RL = 100Ω

10.9

11.1

±V

10.7

±V

VS = ±12V, IL = 250mA

10.6

10.9

±V

10.4

±V

VS = ±5V, RL = 25Ω

3.7

±V

3.5

±V

VS = ±5V, IL = 250mA

3.6

3.9

±V

3.4

±V

IOUT

Maximum Output Current

VS = ±12V, RL = 1Ω

500

1200

Supply Current per Amplifier

VS = ±12V, RBIAS = 24.9k (Note 7)

8.0

13.5

6.7

15.0

VS = ±12V, RBIAS = 32.4k (Note 7)

VS = ±12V, RBIAS = 43.2k (Note 7)

VS = ±12V, RBIAS = 66.5k (Note 7)

VS = ±5V, RBIAS = 24.9k (Note 7)

2.2

3.4

5.0

1.8

5.8

Supply Current in Shutdown

VSHDN = 0.4V

0.1

Output Leakage in Shutdown

VSHDN = 0.4V

0.3

Channel Separation

VS = ±12V, VOUT = ±10V, RL = 40Ω (Note 8)

110

Slew Rate

VS = ±12V, AV = – 10, (Note 9)

300

600

µs

VS = ±5V, AV = –10, (Note 9)

100

200

µs

HD2

Differential 2nd Harmonic Distortion

VS = ±12V, AV = 10, 2VP-P, RL = 50Ω, 1MHz

– 85

dBc

HD3

Differential 3rd Harmonic Distortion

VS = ±12V, AV = 10, 2VP-P, RL = 50Ω, 1MHz

– 82

dBc

GBW

Gain Bandwidth

f = 1MHz

200

MHz

Note 1: Absolute Maximum Ratings are those values beyond which the life

of a device may be impaired.

Note 2: Applies to short circuits to ground only. A short circuit between

the output and either supply may permanently damage the part when

operated on supplies greater than

±10V.

Note 3: The LT6301C is guaranteed to meet specified performance from

°C to 70°C and is designed, characterized and expected to meet these

extended temperature limits, but is not tested at – 40

°C and 85°C. The

LT6301I is guaranteed to meet the extended temperature limits.

Note 4: Thermal resistance varies depending upon the amount of PC board

metal attached to Pins 1, 14, 15, 28 and the exposed bottom side metal of

the device. If the maximum dissipation of the package is exceeded, the

device will go into thermal shutdown and be protected.

Note 5: Guaranteed by the CMRR tests.

Note 6: Matching is between amplifiers A and B or between amplifiers

C and D.

Note 7: RBIAS is connected between V

+ and each SHDN pin, with each

SHDNREF pin grounded.

Note 8: Channel separation is measured between amplifiers A and B and

between amplifiers C and D. Channel separation between any other

combination of amplifiers is guaranteed by design as two separate die are

used in the package.

Note 9: Slew rate is measured at

±5V on a ±10V output signal while

operating on

±12V supplies and ±1V on a ±3V output signal while

operating on

±5V supplies.

LT1794 датащи(PDF) 3 Page - Linear Technology

LT1794 датащи(HTML) 3 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

датащи скачать

ссылки URL