CS5.241, CS5.241-C1, CS5.241-S1

C-Line

13. EMC

The power supply is suitable for applications in industrial environment as well as in residential, commercial and light

industry environment. Restrictions apply on public mains (PFC), see chapter 1 for more information.

A detailed EMC report is available on request.

EMC Immunity

According generic standards: EN 61000-6-1 and EN 61000-6-2

Electrostatic discharge

EN 61000-4-2

contact discharge

air discharge

8kV

15kV

Criterion A

Criterion A

Electromagnetic RF field

EN 61000-4-3

80MHz-2.7GHz

10V/m

Criterion A

Fast transients (Burst)

EN 61000-4-4

input lines

output lines

4kV

2kV

Criterion A

Criterion A

Surge voltage on input

EN 61000-4-5

L

N

L

PE, N

PE

2kV

4kV

Criterion A

Criterion A

Surge voltage on output

EN 61000-4-5

+

-

+ / -

PE

500V

1kV

Criterion A

Criterion A

Conducted disturbance

EN 61000-4-6

0.15-80MHz

10V

Criterion A

Mains voltage dips

EN 61000-4-11

0% of 100Vac

40% of 100Vac

70% of 100Vac

0% of 200Vac

40% of 200Vac

70% of 200Vac

0Vac, 20ms

40Vac, 200ms

70Vac, 500ms

0Vac, 20ms

80Vac, 200ms

140Vac, 500ms

Criterion A

Criterion C

Criterion A

Criterion A

Criterion C

Criterion A

Voltage interruptions

EN 61000-4-11

5000ms

Criterion C

Powerful transients

VDE 0160

over entire load range

750V, 1.3ms

Criterion A

Criterions:

A:

Power supply shows normal operation behavior within the defined limits.

B:

Temporary voltage dips possible. No change in operation mode.

C:

Temporary loss of function is possible. Power supply may shut-down and restarts by itself. No damage or hazards for the power supply

will occur.

EMC Emission

According generic standards: EN 61000-6-4

Conducted emission

input lines

EN 55011, EN 55022, FCC Part 15, CISPR 11, CISPR 22

Class B

Conducted emission

IEC/CISPR 16-1-2, IEC/CISPR 16-2-1

limits for DC power port

according EN 61000-6-3 not

fulfilled

Radiated emission

EN 55011, EN 55022

Class B

Harmonic input current

EN 61000-3-2

not fulfilled at output currents

above 2.7A

Voltage fluctuations, flicker

EN 61000-3-3

This device complies with FCC Part 15 rules.

Operation is subjected to following two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause undesired operation.

*)

tested with constant current loads, non pulsing

**) for information only, not mandatory for EN 61000-6-3

Switching frequency

175kHz to 225kHz

100kHz to 130kHz

Main converter, input voltage dependent at 24V, 2.5A

Main converter, input voltage dependent at 24V, 5A

Jul. 2015 / Rev. 2.0 DS-CS5.241-EN

All parameters are specified at 24V, 5A, 230Vac, 50Hz, 25°C ambient and after a 5 minutes run-in time unless otherwise noted.

www.pulspower.com Phone +49 89 9278 0

Germany

14/25