DIT4192IPWR datasheet(12/22 Pages) TI

12 / 22 page

DIT4192

SBOS229B

www.ti.com

CONTROL REGISTER DEFINITIONS

(SOFTWARE MODE ONLY)

This section defines the control registers used to configure

the DIT4192, as well as the status register used to indicate

an interrupt source.

When MONO = 1 and MCSD = 0, the MDAT bit

is used to select the source for Audio data.

When MONO = 1 and MCSD = 1, the MDAT bit

is used to select the source for both Audio and

Channel Status data.

MCSD

Channel Status Data Selection (Defaults to 0)

When set to 0, Channel A data is used for the A

sub-frame, while Channel B data is used for the

B sub-frame.

When set to 1, use the same channel status data

for both A and B sub-frames. Channel status data

source is selected using the MDAT bit.

TXOFF

Transmitter Output Disable (Defaults to 0)

When set to 0, the line driver outputs, TX–

(pin 17) and TX+ (pin 18) are enabled.

When set to 1, the line driver outputs are forced

to ground.

Bit 7 (MSB)

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0 (LSB)

RST

CLK1

CLK0

PDN

Bit 7 (MSB)

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0 (LSB)

ISYNC

ISCLK

DELAY

JUS

WLEN1

WLEN0

SCLKR

M/S

Bit 7 (MSB)

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0 (LSB)

Bit 7 (MSB)

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0 (LSB)

TXOFF

MCSD

MDAT

MONO

BYPAS

MUTE

VAL

BLSM

Block Start Mode (Defaults to 0)

When set to 0, BLS (pin 25) is configured as an

input pin.

When set to 1, BLS (pin 25) is configured as an

output pin.

VAL

Audio Data Valid (Defaults to 0)

When set to 0, valid Linear PCM audio data is

indicated.

When set to 1, invalid audio data or non-PCM

data is indicated.

MUTE

Transmitter Mute (Defaults to 0)

When set to 0, the mute function is disabled.

When set to 1, the mute function is enabled,

with Channel A and B audio data set to all 0’s.

BYPASS

Transmitter Bypass—AES-3 Data Source for

the Output Driver (Defaults to 0)

When set to 0, AES-3 encoded data is taken

from the output of the on-chip encoder.

When set to 1, RXP (pin 9) is used as the

source for AES-3 encoded data.

MONO

Mono Mode Control (Defaults to 0)

When set to 0, the transmitter is set to Stereo

mode.

When set to 1, the transmitter is set to Mono

mode.

MDAT

Data Selection Bit (Defaults to 0)

(0 = Left Channel, 1 = Right Channel)

When MONO = 0 and MCSD = 0, the MDAT bit

is ignored.

When MONO = 0 and MCSD = 1, the MDAT bit

is used to select the source for Channel Status

data.

PDN

Power-Down (Defaults to 1)

When set to 0, the DIT4192 operates normally.

When set to 1, the DIT4192 is powered down,

with the line driver outputs forced to ground.

CLK[1:0]

MCLK Rate Selection

These bits are used to select the master clock

frequency applied to the MCLK input (pin 6).

CLK1

CLK0

MCLK Rate

128 • fS

256 • fS (default)

384 • fS

512 • fS

RST

Software Reset (Defaults to 0)

When set to 0, the DIT4192 operates normally.

When set to 1, the DIT4192 is reset.

M/S

Master/Slave Mode (Defaults to 0)

When set to 0, the audio serial port is set for

Slave operation.

When set to 1, the audio serial port is set for

Master operation.

DIT4192IPWR датащи(PDF) 12 Page - Texas Instruments

DIT4192IPWR датащи(HTML) 12 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

датащи скачать

ссылки URL