RN2903 datasheet(14/24 Pages) MICROCHIP

14 / 24 page

RN2903

DS50002390B-page 14

 2015 Microchip Technology Inc.

6.1.2

RF EXPOSURE

All transmitters regulated by FCC must comply with RF

exposure requirements. KDB 447498 General RF

Exposure Guidance provides guidance in determining

whether proposed or existing transmitting facilities,

operations or devices comply with limits for human

exposure to Radio Frequency (RF) fields adopted by

the Federal Communications Commission (FCC).

From the RN2903 FCC Grant: Output power listed is

conducted. This grant is valid only when the module is

sold to OEM integrators and must be installed by the

OEM or OEM integrators. This transmitter is restricted

for use with the specific antenna(s) tested in this

application for Certification and must not be co-located

or operating in conjunction with any other antenna or

transmitters within a host device, except in accordance

with FCC multi-transmitter product procedures.

6.1.3

APPROVED EXTERNAL ANTENNA

TYPES

To maintain modular approval in the United States, only

the antenna types that have been tested shall be used.

It is permissible to use different antenna manufacturer

provided the same antenna type and antenna gain

(equal to or less than) is used.

Testing of the RN2903 module was performed with the

antenna types listed in Table 5-1 Tested External

Antenna Types.

6.1.4

HELPFUL WEB SITES

Federal Communications Commission (FCC):

http://www.fcc.gov

FCC Office of Engineering and Technology (OET)

Laboratory Division Knowledge Database (KDB):

https://apps.fcc.gov/oetcf/kdb/index.cfm

6.2

Canada

The RN2903 module has been certified for use in

Canada under Industry Canada (IC) Radio Standards

Specification (RSS) RSS-210 and RSS-Gen. Modular

approval permits the installation of a module in a host

device without the need to recertify the device.

6.2.1

LABELING AND USER

INFORMATION REQUIREMENTS

Labeling Requirements for the Host Device (from

Section 3.2.1, RSS-Gen, Issue 3, December 2010):

The host device shall be properly labeled to identify the

module within the host device.

The Industry Canada certification label of a module

shall be clearly visible at all times when installed in the

host device, otherwise the host device must be labeled

to display the Industry Canada certification number of

the module, preceded by the words “Contains

transmitter module”, or the word “Contains”, or similar

wording expressing the same meaning, as follows:

User Manual Notice for License-Exempt Radio

Apparatus (from Section 7.1.3 RSS-Gen, Issue 3,

December 2010): User manuals for license-exempt

radio apparatus shall contain the following or

equivalent notice in a conspicuous location in the user

manual or alternatively on the device or both:

Transmitter Antenna (from Section 7.1.2 RSS-Gen,

Issue 3, December 2010): User manuals for

transmitters shall display the following notice in a

conspicuous location:

The above notice may be affixed to the device instead

of displayed in the user manual.

Contains transmitter module IC: 6514A-RN2903.

This device complies with Industry Canada license-

exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not

cause interference, and (2) this device must accept

any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Indus-

trie Canada applicables aux appareils radio exempts

de licence. L'exploitation est autorisée aux deux con-

ditions suivantes: (1) l'appareil ne doit pas produire

de brouillage, et (2) l'utilisateur de l'appareil doit

accepter tout brouillage radioélectrique subi, même si

le brouillage est susceptible d'en compromettre le

fonctionnement.

Under Industry Canada regulations, this radio trans-

mitter may only operate using an antenna of a type

and maximum (or lesser) gain approved for the trans-

mitter by Industry Canada. To reduce potential radio

interference to other users, the antenna type and its

gain should be so chosen that the equivalent isotrop-

ically radiated power (e.i.r.p.) is not more than that

necessary for successful communication.

Conformément à la réglementation d'Industrie Can-

ada, le présent émetteur radio peut fonctionner avec

une antenne d'un type et d'un gain maximal (ou

inférieur) approuvé pour l'émetteur par Industrie Can-

ada. Dans le but de réduire les risques de brouillage

radioélectrique à l'intention des autres utilisateurs, il

faut choisir le type d'antenne et son gain de sorte que

la puissance isotrope rayonnée équivalente (p.i.r.e.)

ne dépasse pas l'intensité nécessaire à l'établisse-

ment d'une communication satisfaisante.

RN2903 датащи(PDF) 14 Page - Microchip Technology

RN2903 датащи(HTML) 14 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

датащи скачать

ссылки URL