DA9211 datasheet(44/74 Pages) DIALOG

44 / 74 page

DA9211 and DA9212

Datasheet

Company confidential

Data sheet

Version <3.0>

<07-Jan-2015>

CFR0011-120-00 Rev 3

44 of 74

Table 14: 4-WIRE Interface Summary

Parameters

Signal Lines

nCS

Chip select

SI Serial input data

Master out Slave in

SO Serial output data

Master in Slave out

Transmission clock

Interface

Push-pull with tristate

Supply voltage

Selected from VDDIO

1.6 V to 3.3 V

Data rate

Effective read/write data

Up to 7 Mbps

Transmission

Half-duplex

MSB first

16 bit cycles

7-bit address, 1 bit read/write, 8-bit data

Configuration

CPOL

Clock polarity

CPHA

Clock phase

nCS_POL

nCS is active low/high

Note that reading the same register at high clock rates directly after writing it does not guarantee a

correct value. It is recommended to keep a delay of one frame until re-accessing a register that has

just been written (for example, by writing/reading another register address in between).

2-WIRE Communication

13.4.2

The IF_TYPE bit in the INTERFACE2 register can be used to configure the DA9211 and DA9212

control interface as a 2-WIRE serial data interface. In this case the GPIO3 and GPI4 are free for

regular input/output functions. DA9211 and DA9212 has a configurable device write address (default:

0xD0) and a configurable device read address (default: 0xD1). See control IF_BASE_ADDR1 for

details of configurable addresses. The ADDR_SEL_CONF bit is used to configure the device

address as IF_BASE_ADDR1 or IF_BASE_ADDR2 depending on the voltage level applied at a

configurable GPI port (see GPIO Extender).

The SK port functions as the 2-WIRE clock and the SI port carries all the power manager

bi-directional 2-WIRE data. The 2-WIRE interface is open-drain supporting multiple devices on a

single line. The bus lines have to be pulled HIGH by external pull-up resistors (in the 2 k

Ω to 20 kΩ

range). The attached devices only drive the bus lines LOW by connecting them to ground. As a result

two devices cannot conflict if they drive the bus simultaneously. In standard/fast mode the highest

frequency of the bus is 400 kHz. The exact frequency can be determined by the application and does

not have any relation to the DA9211 and DA9212 internal clock signals. DA9211 and DA9212 will

follow the host clock speed within the described limitations, and does not initiate any clock arbitration

or slow down. An automatic interface reset can be triggered using control 2WIRE_TO if the clock

signal stops to toggle for more than 35 ms.

The interface supports operation compatible to Standard, Fast, Fast-Plus and High Speed mode of

the I2C-bus specification Rev 4. Operation in high speed mode at 3.4 MHz requires mode changing

in order to set spike suppression and slope control characteristics to be compatible with the I2C-bus

specification. The high speed mode can be enabled on a transfer by transfer basis by sending the

master code (0000 1XXX) at the begin of the transfer. DA9211 and DA9212 do not make use of

clock stretching, and deliver read data without additional delay up to 3.4 MHz.

Alternatively, PM_IF_HSM configures the interface to use high speed mode continuously. In this

case, the master code is not required at the beginning of every transfer. This reduces the

communication overhead on the bus but limits the slaves attachable to the bus to compatible

devices.

DA9211 датащи(PDF) 44 Page - Dialog Semiconductor

DA9211 датащи(HTML) 44 Page - Dialog Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74

датащи скачать

ссылки URL