TSB43AB21 datasheet(21/109 Pages) TI

21 / 109 page

2–9

Table 2–8. Power Supply Terminals

TERMINAL

TYPE

I/O

DESCRIPTION

NAME

NO.

TYPE

I/O

DESCRIPTION

AGND

109–111, 117,

126–128

Supply

–

Analog circuit ground terminals. These terminals must be tied together to the low-impedance

circuit board ground plane.

AVDD

1, 2, 107, 108,

120

Supply

–

Analog circuit power terminals. A parallel combination of high frequency decoupling capacitors

near each terminal is suggested, such as 0.1

µF and 0.001 µF. Lower frequency 10-µF filtering

capacitors are also recommended. These supply terminals are separated from PLLVDD and

DVDD internal to the device to provide noise isolation. They must be tied at a low-impedance

point on the circuit board.

DGND

17, 23, 33, 44,

55, 64, 68, 75,

83, 103

Supply

–

Digital circuit ground terminals. These terminals must be tied together to the low-impedance

circuit board ground plane.

DVDD

15, 27, 39, 51,

59, 72, 88,

100

Supply

–

Digital circuit power terminals. A parallel combination of high frequency decoupling capacitors

near each DVDD terminal is suggested, such as 0.1 µF and 0.001 µF. Lower frequency 10-µF

filtering capacitors are also recommended. These supply terminals are separated from PLLVDD

and AVDD internal to the device to provide noise isolation. They must be tied at a low-impedance

point on the circuit board.

PLLGND

Supply

–

PLL circuit ground terminal. This terminal must be tied to the low-impedance circuit board

ground plane.

PLLVDD

Supply

–

PLL circuit power terminal. A parallel combination of high frequency decoupling capacitors near

the terminal is suggested, such as 0.1

µF and 0.001 µF. Lower frequency 10-µF filtering

capacitors are also recommended. This supply terminal is separated from DVDD and AVDD

internal to the device to provide noise isolation. It must be tied to a low-impedance point on the

circuit board.

REG18

30, 93

Supply

–

REG18. 1.8-V power supply for the device core. If the internal voltage regulator is enabled

(REG_EN is tied low), these terminals must be left unconnected. The internal voltage regulator

provides 1.8 V from DVDD. When the internal regulator is disabled (REG_EN is high), the

REG18 terminals can be used to supply an external 1.8-V supply to the TSB43AB21 core. It

is recommended that 0.1-

µF bypass capacitors be used and placed close to these terminals.

VDDP

20, 35, 48, 62,

Supply

–

PCI signaling clamp voltage power input. PCI signals are clamped per the PCI Local Bus

Specification. In addition, if a 5-V ROM is used, the VDDP must be connected to 5 V.

TSB43AB21 датащи(PDF) 21 Page - Texas Instruments

TSB43AB21 датащи(HTML) 21 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL