| поискавой системы для электроныых деталей |
|
LMF100CIWM датащи(PDF) 6 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
LMF100CIWM датащи(HTML) 6 Page - Texas Instruments |
|
6 / 42 page ![]() Not Recommended for New Designs LMF100 SNOSBG9B – JULY 1999 – REVISED JUNE 2015 www.ti.com Electrical Characteristics for V + = +5 V and V− = −5 V (continued) The following specifications apply for Mode 1, Q = 10 (R1 = R3 = 100 k, R2 = 10 k), V + = +5 V and V− = −5 V unless otherwise specified. All limits are TA = TJ = 25°C unless otherwise specified. LMF100CCN LMF100CIWM PARAMETER TEST CONDITIONS UNIT MIN TYP MAX MIN TYP MAX ±30 ±30 ±80 Tested Limit (1) mV SA/B = V + TMIN to TMAX ±80 Design Limit (2) TMIN to TMAX ±80 VOS2 DC Offset voltage (4) fCLK = 250 kHz ±15 ±15 ±70 Tested Limit (1) mV SA/B = V – TMIN to TMAX ±70 Design Limit (2) TMIN to TMAX ±70 ±15 ±15 ±40 Tested VOS3 DC Offset voltage (4) fCLK = 250 kHz Limit (1) mV TMIN to TMAX ±60 Design TMIN to TMAX ±60 Limit (2) Crosstalk (5) A Side to B Side or B Side to A Side –60 –60 dB fCLK = 250 kHz N 40 40 Output noise (6) 20 kHz Bandwidth BP 320 320 µV 100:1 Mode LP 300 300 Clock feedthrough (7) fCLK = 250 kHz 100:1 Mode 6 6 mV 4 4 −4.7 −4.7 ±3.8 RL = 5 k Tested (All Outputs) Limit (1) TMIN to TMAX ±3.7 VOUT Minimum output voltage swing V Design TMIN to TMAX ±3.7 Limit (2) RL = 3.5 k 3.9 3.9 (All Outputs) −4.6 −4.6 GB Operational amplifier gain BW 5 5 MHz W product SR Operational amplifier slew rate 20 20 V/µs Source All Outputs 12 12 mA Maximum output, Isc Short circuit current (8) Sink All Outputs 45 45 mA Tested Limit (1) 10 Input current on Pins: 4, 5, 6, 9, IIN µA 10, 11, 12, 16, 17 Design Limit (2) TMIN to TMAX 10 (5) Crosstalk between the internal filter sections is measured by applying a 1 VRMS 10-kHz signal to one bandpass filter section input and grounding the input of the other bandpass filter section. The crosstalk is the ratio between the output of the grounded filter section and the 1 VRMS input signal of the other section. (6) In 50:1 mode the output noise is 3 dB higher. (7) In 50:1 mode the clock feed through is 6 dB higher. (8) The short circuit source current is measured by forcing the output that is being tested to its maximum positive voltage swing and then shorting that output to the negative supply. The short circuit sink current is measured by forcing the output that is being tested to its maximum negative voltage swing and then shorting that output to the positive supply. These are the worst case conditions. 6.6 Electrical Characteristics for V + = +2.5 V and V− = −2.5 V The following specifications apply for Mode 1, Q = 10 (R1 = R3 = 100 k, R2 = 10 k), V + = +2.50 V and V− = −2.50 V unless otherwise specified. All limits are TA = TJ = 25°C unless otherwise specified. LMF100CCN LMF100CIWM PARAMETER TEST CONDITIONS UNIT MIN TYP MAX MIN TYP MAX 8 8 12 12 Tested fCLK = 250 kHz, Is Maximum supply current Limit (1) mA TMIN to TMAX No Input Signal Design 12 Limit (2) f0 Center frequency 0.1 50000 0.1 50000 Hz (1) Tested limits are specified to Texas Instruments AOQL (Average Outgoing Quality Level). (2) Design limits are specified to Texas Instruments AOQL (Average Outgoing Quality Level) but are not 100% tested. 6 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated Product Folder Links: LMF100 |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |