WM8750 datasheet(48/60 Pages) WOLFSON

48 / 60 page

WM8750BL

Production Data

PD, Rev 4.1, August 2012

STOPPING THE MASTER CLOCK

In order to minimise power consumed in the digital core of the WM8750BL, the master clock may be

stopped in Standby and OFF modes. If this cannot be done externally at the clock source, the

DIGENB bit (R25, bit 0) can be set to stop the MCLK signal from propagating into the device core. In

Standby mode, setting DIGENB will typically provide an additional power saving on DCVDD of 20uA.

However, since setting DIGENB has no effect on the power consumption of other system components

external to the WM8750BL, it is preferable to disable the master clock at its source wherever

possible.

ADDRESS

BIT

LABEL

DEFAULT

DESCRIPTION

R25 (19h)

Additional Control

(1)

DIGENB

Master clock disable

0: master clock enabled

1: master clock disabled

Table 44 ADC and DAC Oversampling Rate Selection

NOTE: Before DIGENB can be set, the control bits ADCL, ADCR, DACL and DACR must be set

to zero and a waiting time of 1ms must be observed. Any failure to follow this procedure may

prevent DACs and ADCs from re-starting correctly.

SAVING POWER BY REDUCING OVERSAMPLING RATE

The default mode of operation of the ADC and DAC digital filters is in 128x oversampling mode.

Under the control of ADCOSR and DACOSR the oversampling rate may be halved. This will result in

a slight decrease in noise performance but will also reduce the power consumption of the device. In

USB mode ADCOSR must be set to 0, i.e. 128x oversampling.

ADDRESS

BIT

LABEL

DEFAULT

DESCRIPTION

R24 (18h)

Additional Control

(2)

ADCOSR

ADC oversample rate select

1 = 64x (lowest power)

0 = 128x (best SNR)

DACOSR

DAC oversample rate select

1 = 64x (lowest power)

0 = 128x (best SNR)

Table 45 ADC and DAC Oversampling Rate Selection

ADCOSR set to ‘1’, 64x oversample mode, is not supported in USB mode (USB=1).

SAVING POWER AT HIGHER SUPPLY VOLTAGES

The analogue supplies to the WM8750BL can run from 1.8V to 3.6V. By default, all analogue circuitry

on the device is optimized to run at 3.3V. This set-up is also good for all other supply voltages down

to 1.8V. At lower voltages, performance can be improved by increasing the bias current. If low power

operation is preferred the bias current can be left at the default setting. This is controlled as shown

below.

ADDRESS

BIT

LABEL

DEFAULT

DESCRIPTION

R23 (17h)

Additional

Control(1)

7:6

VSEL

[1:0]

Analogue Bias optimization

00: Highest bias current, optimized for AVDD=1.8V

01: Bias current optimized for AVDD=2.5V

1X: Lowest bias current, optimized for AVDD=3.3V

WM8750 датащи(PDF) 48 Page - Wolfson Microelectronics plc

WM8750 датащи(HTML) 48 Page - Wolfson Microelectronics plc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

датащи скачать

ссылки URL