CC1021-RTR1 datasheet(25/91 Pages) TI1

25 / 91 page

[

]

ref

9.8304

MHz

512

[

]

ref

9.8304

MHz

256

xosc

ref

REF _ DIV

ref

FREQ

0.5

DITHER

16384

ref

FREQ

0.5

DITHER

32768

Not Recommended for New Designs NRND

CC1021

www.ti.com

SWRS045D – JANUARY 2006 – REVISED JANUARY 2015

5.8

Frequency Programming

Programming the frequency word in the configuration registers sets the operation frequency. There are

two frequency words registers, termed FREQ_A and FREQ_B, which can be programmed to two different

frequencies. One of the frequency words can be used for RX (local oscillator frequency) and the other for

TX (transmitting carrier frequency) in order to be able to switch very fast between RX mode and TX mode.

They can also be used for RX (or TX) at two different channels. The F_REG bit in the MAIN register

selects frequency word A or B.

The frequency word is located in FREQ_2A:FREQ_1A:FREQ_0A and FREQ_2B:FREQ_1B:FREQ_0B for

the FREQ_A and FREQ_B word respectively. The LSB of the FREQ_0 registers are used to enable

dithering (see Section 5.8.1).

The PLL output frequency is given by Equation 2 in the frequency band 402 to 470 MHz, and by

Equation 3 in the frequency band 804 to 960 MHz.

(2)

(3)

The BANDSELECT bit in the ANALOG register controls the frequency band used. BANDSELECT = 0

gives 402 to 470 MHz, and BANDSELECT = 1 gives 804 to 960 MHz.

The reference frequency is the crystal oscillator clock frequency divided by REF_DIV (3 bits in the

CLOCK_A or CLOCK_B register), a number between 1 and 7, as shown in Equation 4.

(4)

FSK frequency deviation is programmed in the DEVIATION register. The deviation programming is divided

into a mantissa (TXDEV_M[3:0]) and an exponent (TXDEV_X[2:0]).

Generally REF_DIV should be as low as possible, but the requirements shown in Equation 5 must be met

in the frequency band 402 to 470 MHz.

(5)

The requirements shown in Equation 6 must be met in the frequency band 804 to 960 MHz.

(6)

The PLL output frequency equations give the carrier frequency, fc , in transmit mode (centre frequency).

The two FSK modulation frequencies are given by Equation 7 and Equation 8.

f0 = fc – fdev

(7)

f1 = fc + fdev

(8)

Where:

fdev is set by the DEVIATION register.

fdev is set by the DEVIATION register shown in Equation 9 in the frequency band 402 to 470 MHz.

fdev = fref × TXDEV_M × 2

(TXDEV_X –16)

(9)

fdev is set by the DEVIATION register shown in Equation 10 in the frequency band 804 to 960 MHz.

fdev = fref × TXDEV_M × 2

(TXDEV_X –15)

(10)

OOK (On-Off Keying) is used if TXDEV_M[3:0] = 0000.

The TX_SHAPING bit in the DEVIATION register controls Gaussian shaping of the modulation signal.

Detailed Description

Submit Documentation Feedback

Product Folder Links: CC1021

CC1021-RTR1 датащи(PDF) 25 Page - Texas Instruments

CC1021-RTR1 датащи(HTML) 25 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91

датащи скачать

ссылки URL