COP688CL datasheet(20/40 Pages) NSC

20 / 40 page

Multi-Input Wakeup

The Multi-Input Wakeup feature is used to return (wakeup)

the device from either the HALT or IDLE modes Alternately

Multi-Input WakeupInterrupt feature may also be used to

generate up to 8 edge selectable external interrupts

Figure 10 shows the Multi-Input Wakeup logic

The Multi-Input Wakeup feature utilizes the L Port The user

selects which particular L port bit (or combination of L Port

bits) will cause the device to exit the HALT or IDLE modes

The selection is done through the Reg WKEN The Reg

WKEN is an 8-bit readwrite register which contains a con-

trol bit for every L port bit Setting a particular WKEN bit

enables a Wakeup from the associated L port pin

The user can select whether the trigger condition on the

selected L Port pin is going to be either a positive edge (low

to high transition) or a negative edge (high to low transition)

This selection is made via the Reg WKEDG which is an 8-

bit control register with a bit assigned to each L Port pin

Setting the control bit will select the trigger condition to be a

negative edge on that particular L Port pin Resetting the bit

selects the trigger condition to be a positive edge Changing

an edge select entails several steps in order to avoid a

pseudo Wakeup condition as a result of the edge change

First the associated WKEN bit should be reset followed by

the edge select change in WKEDG Next the associated

WKPND bit should be cleared followed by the associated

WKEN bit being re-enabled

An example may serve to clarify this procedure Suppose

we wish to change the edge select from positive (low going

high) to negative (high going low) for L Port bit 5 where bit 5

has previously been enabled for an input interrupt The pro-

gram would be as follows

RBIT

WKEN

SBIT

WKEDG

RBIT

WKPND

SBIT

WKEN

If the L port bits have been used as outputs and then

changed to inputs with Multi-Input WakeupInterrupt a safe-

ty procedure should also be followed to avoid inherited

pseudo wakeup conditions After the selected L port bits

have been changed from output to input but before the as-

sociated WKEN bits are enabled the associated edge se-

lect bits in WKEDG should be set or reset for the desired

edge selects followed by the associated WKPND bits being

cleared

This same procedure should be used following reset since

the L port inputs are left floating as a result of reset

The occurrence of the selected trigger condition for Multi-In-

put Wakeup is latched into a pending register called

WKPND The respective bits of the WKPND register will be

set on the occurrence of the selected trigger edge on the

corresponding Port L pin The user has the responsibility of

clearing these pending flags Since WKPND is a pending

the device will not enter the HALT mode if any Wakeup bit is

both enabled and pending Consequently the user has the

responsibility of clearing the pending flags before attempt-

ing to enter the HALT mode

The WKEN WKPND and WKEDG are all readwrite regis-

ters and are cleared at reset

PORT L INTERRUPTS

Port L provides the user with an additional eight fully select-

able edge sensitive interrupts which are all vectored into

the same service subroutine

The interrupt from Port L shares logic with the wake up cir-

cuitry The register WKEN allows interrupts from Port L to

TLDD9766 – 16

FIGURE 10 Multi-Input Wake Up Logic

http

www nationalcom

COP688CL датащи(PDF) 20 Page - National Semiconductor (TI)

COP688CL датащи(HTML) 20 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

датащи скачать

ссылки URL