TDA9116 datasheet(31/47 Pages) STMICROELECTRONICS

31 / 47 page

TDA9116

31/47

age adjusted via

HMOIRE I2C bus control is output

on pin HMoiré for control purposes.

The behaviour of horizontal moiré is to be opti-

mised for different deflection design configurations

using HMoiré I2C bus bit. This bit is to be kept at 0

for common architecture (B+ and EHT common

regulation) and at 1 for separated architecture (B+

and EHT each regulated separately).

Figure 10. Control of HOut and BOut at start/stop at nominal Vcc

10.4 - VERTICAL SECTION

10.4.1 - General

The goal of the vertical section is to drive vertical

deflection output stage. It delivers a sawtooth

waveform with an amplitude independent of de-

flection frequency, on which vertical geometry cor-

rections of C- and S-type are superimposed (see

chapter TYPICAL OUTPUT WAVEFORMS).

Block diagram is in Figure 11. The sawtooth is ob-

tained by charging an external capacitor on pin

VCap with controlled current and by discharging it

via transistor Q1. This is controlled by the CON-

TROLLER. The charging starts when the voltage

across the capacitor drops below VVOB threshold.

The discharging starts either when it exceeds

VVOT threshold or a short time after arrival of syn-

chronization pulse. This time is necessary for the

AGC loop to sample the voltage at the top of the

sawtooth. The VVOB reference is routed out onto

VOscF pin in order to allow for further filtration.

The charging current influences amplitude and

shape of the sawtooth. Just before the discharge,

the voltage across the capacitor on pin VCap is

sampled and stored on a storage capacitor con-

nected on pin VAGCCap. During the following ver-

tical period, this voltage is compared to internal

reference REF (VVOT), the result thereof control-

ling the gain of the transconductance amplifier pro-

viding the charging current. Speed of this AGC

loop depends on the storage capacitance on pin

VAGCCap. The VLock I2C bus flag is set to 1

when the loop is stabilized, i.e. when the voltage

on pin VAGCCap matches VVOT value. On the

screen, this corresponds to stabilized vertical size

of picture. After a change of frequency on the

sync. input, the stabilization time depends on the

frequency difference and on the capacitor value.

The lower its value, the shorter the stabilization

time, but on the other hand, the lower the loop sta-

bility. A practical compromise is a capacitance of

470nF. The leakage current of this capacitor re-

sults in difference in amplitude between low and

high frequencies. The higher its parallel resistance

RL(VAGCCap), the lower this difference.

When the synchronization pulse is not present, the

charging current is fixed. As a consequence, the

free-running frequency fVO(0) only depends on the

value of the capacitor on pin VCap. It can be

roughly calculated using the following formula

V(HPosF)

Soft start

Soft stop

Normal operation

Start

HOut

Start

BOut

Stop

HOut

Stop

BOut

HOut

H-duty cycle

BOut (positive)

B-duty cycle

100%

VHOn

VBOn

VHBNorm

VHPosMax

VHPosMin

HPOS (I2C)

range

minimum value

maximum value

TDA9116 датащи(PDF) 31 Page - STMicroelectronics

TDA9116 датащи(HTML) 31 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47

датащи скачать

ссылки URL