TC1307 datasheet(4/28 Pages) MICROCHIP

4 / 28 page

TC1307

DS21702A-page 4

 2002 Microchip Technology Inc.

Reset Threshold Voltage

VTH

2.59

2.55

2.63

—

2.66

2.70

TA = +25°C

TA = -40°C to +125°C

See Figure 4-2

Reset Circuit Supply Current

IVDET

—

µA

RESET = Open

Reset Threshold Voltage

Temperature Coefficient

VTH-TEMP

—30

—

ppm/°C

Detect Threshold to RESET

Active Time Delay

TVDET-RESET

—

135

—

µsec

VDET = VTH to VTH - 100 mV,

See Figure 4-2

Reset Time-out Period

TRESET

140

300

560

msec

See Figure 4-2

RESET Output Voltage Low

VOL-RES

——

0.3

VVDET = VTH-min

ISINK = 1.2 mA

——

0.4

VDET = VTH-min

ISINK = 3.2 mA

——

0.3

VDET > 1.0V ISINK = 50 µA

Note 8, See Figure 4-2

RESET Output Voltage High

VOH-RES

0.8*VDET

VDET-

1.5V

——

ISOURCE = 500 µA

Isource = 800 µA

VDET>VTH-max (Both cases),

See Figure 4-2

Temperature Ranges:

Maximum Junction Temperature

Range

-40

—

+150

°C

Maximum Junction Temperature

Range

-40

—

+125

°C

Storage Temperature Range

-65

—

+150

°C

Thermal Package Resistances:

Thermal Resistance, 16L-QSOP

θJA

—

112.4

—

°C/W

EIA/JEDEC JESD51-751-7

4 Layer Board

Unless otherwise specified, all limits are established for VIN = VR+1, IL = 100 µA, CL = 3.3 µF, SHDN > VIH, TA = 25°C.

Boldface type specifications apply for junction temperatures, TJ (Note 9) of -40°C to +125°C.

Parameter

Sym

Min

Typ

Max

Units

Conditions

Note 1: The minimum VIN must meet two conditions: VIN ≥ 2.7V and VIN ≥ (VR + 2.5%) + VDROPOUT.

2: VR is the nominal regulator output voltage. For example: VR = 1.8V, 2.5V, 2.8V or 3.0V.

3: TCVOUT = (VOUT-HIGH - VOUT-LOW) * 106 / (VR * ∆Temperature), VOUT-HIGH = Highest voltage measured over the tempera-

ture range. VOUT-LOW = Lowest voltage measured over the temperature range.

4: Load regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is

tested over a load range from 1mA to the maximum specified output current. Changes in output voltage due to heating

effects are determined using thermal regulation specification TCVOUT.

5: Thermal regulation is defined as the change in output voltage at a time t after a change in power dissipation is applied.

Specifications are for a current pulse equal to ILMAX at VIN = 6.0V for t = 10 msec.

6: Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value

with a 1V differential applied.

7: The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction temper-

ature and the thermal resistance from junction to air. (i.e. TA, TJ, θJA). Exceeding the maximum allowable power dissipa-

tion will cause the device operating junction temperature to exceed the maximum 150°C rating. Sustained junction

temperatures above 150°C can impact the device reliability.

8: VTH-MIN = 2.55V and VTH-MAX = 2.70V.

9: The Junction temperature is approximated by soaking the device under test at an ambient temperature equal to the

desired Junction temperature. The test time is small enough such that the rise in the Junction temperature over the Ambi-

ent temperature is not significant.

TC1307 датащи(PDF) 4 Page - Microchip Technology

TC1307 датащи(HTML) 4 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

датащи скачать

ссылки URL