LTC1695CS5 datasheet(12/20 Pages) LINER

12 / 20 page

LTC1695

APPLICATIONS INFORMATION

sistor capable of sinking 3mA at less than 0.4V during the

slave acknowledge sequence.

The LTC1695 is compatible with the Philips/Signetics I2C

Bus Interface. The 1.4V threshold for SCL and SDA does

not create any I2C application problems.

Early Stop Conditions

If a stop condition occurs before the data byte is acknowl-

edged in the write byte protocol, the LTC1695’s DAC is not

updated. Otherwise, the internal register is updated with

the new data and VOUT changes accordingly to the new

programmed value.

Address, Command, Data Selection

The LTC1695’s address is hard-wired internally as 1110100

(MSB to LSB, A6 to A0). Consult LTC for parts with

alternate address codes. Consult the Address, Command

and Data Byte Tables for further information and as a

concise reference.

As shown in Figure 2, D5 to D0 in the command code,

control the linear regulator’s output voltage and thus fan

speed. D5 to D0 are sent from the host to the LTC1695

during send byte protocol. The LTC1695 latches D5 to D0

as DAC input data at the falling edge of the data acknowl-

edge signal. The host must set “BST” (boost start enable

bit) to high if the LTC1695’s 250ms boost start timer

option is used. All bits are reset to zero during power-on

reset and UVLO. As shown in the Timing Diagram, bit 6

and bit 7 in the data byte register are defined as thermal

shutdown status (THE) and over current fault (OCF) status

respectively. The LTC1695 sets OCF high if ILOAD exceeds

390mA typically and “THE” high if junction temperature

exceeds 155

°C typically. The remaining bits of the data

byte’s register (bit 5 to 0) are set low during host read

back.

SCL and SDA

SCL is the synchronizing clock signal generated by the

host. SDA is the bidirectional data transfer line between

the host and a slave device. The host initiates a start bit by

pulling SDA from high to low while SCL is high. The stop

bit is initiated by changing SDA from low to high while SCL

is high. All address, command and acknowledge signals

must be valid and should not change while SCL is high.

The acknowledge bit signals to the host the acceptance of

a correct address byte or command byte.

The SCL and SDA input threshold voltages are typically

1.4V with 40mV of hysteresis. Connect the SCL and SDA

open-drain lines to either a resistive or current source pull

up. The LTC1695 SDA has an open-drain N-channel tran-

Figure 2. SMBus Interface Bit Definition

123456789

10 11 12 13 14 15 16 17 18 19

111010000

X BST D5 D4 D3 D2 D1 D0

123456789

10 11 12 13 14 15 16 17 18 19

1110100

OCF THE

00000

SLAVE ADDRESS

S = SMBus START BIT

P = SMBus STOP BIT

BST = 1 ENABLES THE BOOST START TIMER

D5 TO D0 = 6-BIT INPUT CODE FOR THE DAC (D5 = MSB)

OCF = 1 SIGNALS THAT THE LTC1695 IS IN CURRENT LIMIT

THE = 1 SIGNALS THAT THE LTC1695 IS IN THERMAL SHUTDOWN

BIT 18 = 1 IS A NOT ACKNOWLEDGE FOR RECEIVE BYTE PROTOCOL

NOTE: DURING POWER UP AND UVLO, DAC INPUT BITS

(D5 TO D0) AND THE BST BIT ARE RESET TO ZERO

COMMAND BYTE

START

STOP

A6 A5 A4 A3 A2 A1 A0 W

MSB

LSB A

SLAVE ADDRESS

DATA BYTE

START

STOP

A6 A5 A4 A3 A2 A1 A0 W

SMBus SEND BYTE PROTOCOL

SMBus RECEIVE BYTE PROTOCOL

1695 • F02

LTC1695CS5 датащи(PDF) 12 Page - Linear Technology

LTC1695CS5 датащи(HTML) 12 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

датащи скачать

ссылки URL