 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
ADE7166 датащи(PDF) 109 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADE7166 датащи(HTML) 109 Page - Analog Devices |
|
|
109 / 152 page  ADE7116/ADE7156/ADE7166/ADE7169/ADE7566/ADE7569 Rev. B | Page 109 of 1 52 FLASH MEMORY ORGANIZATION The 16 kB array of flash memory provided by the ADE7116/ ADE7156/ADE7166/ADE7169/ADE7566/ADE7569 are segmented into 32 pages of 512 bytes each. It is up to the user to decide which flash memory is to be used for data memory. It is recommended that each page be dedicated solely to program or data memory so that an instance does not arise where the program counter is loaded with data memory instead of an opcode from the program memory or where program memory is erased to update a byte of data memory. 0x3E00 0x3DFF 0x3C00 0x3BFF 0x3A00 0x39FF 0x3800 0x37FF 0x3600 0x35FF 0x3400 0x33FF 0x3200 0x31FF 0x3000 0x2FFF 0x2E00 0x2DFF 0x2C00 0x2BFF 0x2A00 0x29FF 0x2800 0x27FF 0x2600 0x25FF 0x2400 0x23FF 0x2200 0x21FF 0x2000 0x3FFF CONTAINS PROTECTION SETTINGS. READ PROTECT BIT 7 READ PROTECT BIT 6 READ PROTECT BIT 5 READ PROTECT BIT 4 PAGE 30 PAGE 29 PAGE 28 PAGE 27 PAGE 26 PAGE 25 PAGE 24 PAGE 23 PAGE 22 PAGE 21 PAGE 20 PAGE 19 PAGE 18 PAGE 17 PAGE 16 PAGE 31 0x1E00 0x1DFF 0x1C00 0x1BFF 0x1A00 0x19FF 0x1800 0x17FF 0x1600 0x15FF 0x1400 0x13FF 0x1200 0x11FF 0x1000 0x0FFF 0x0E00 0x0DFF 0x0C00 0x0BFF 0x0A00 0x09FF 0x0800 0x07FF 0x0600 0x05FF 0x0400 0x03FF 0x0200 0x01FF 0x0000 0x1FFF READ PROTECT BIT 3 READ PROTECT BIT 2 READ PROTECT BIT 1 READ PROTECT BIT 0 PAGE 14 PAGE 13 PAGE 12 PAGE 11 PAGE 10 PAGE 9 PAGE 8 PAGE 7 PAGE 6 PAGE 5 PAGE 4 PAGE 3 PAGE 2 PAGE 1 PAGE 0 PAGE 15 Figure 94. Flash Memory Organization The flash memory can be protected from read or write/erase access. The protection is implemented in the upper page of user program memory, Page 31. Four of the bytes from this page are used to set up write/erase protection for each page. Another byte is used for configuring read protection of the flash memory. The read protection is selected in groups of four pages. Finally, there is a byte used to store the key required for modifying the protection scheme. The last page of flash memory must be write/erase protected at a minimum. The implication of write/erase protecting the last page is that the content of the 506 bytes in this page that are available to the user must not change. Thus, it is recommended that if code protection is enabled, the last page of user accessible flash memory should be used only to store data that does not need modification in the field. If the firmware requires protection and may need updating in the future, the last page should be reserved for constants used by the user code that do not require modification during emulation or debug. Page 0 through Page 30 are, therefore, available for general program and data memory use. It is recommended that Page 31 be used for constants or code that do not require future modifications. Note that the last six bytes of Page 31 are reserved for the flash memory protection and are, therefore, unavailable to the user. USING THE FLASH MEMORY The 16 kB of flash memory are configured as 32 pages, each comprising 512 bytes. As with the other ADE7116/ADE7156/ ADE7166/ADE7169/ADE7566/ADE7569 peripherals, the interface to this memory space is via a group of registers mapped in the SFR space (see Table 101). The flash data SFR, (EDATA, Address 0xBC) holds the byte of data to be accessed. The byte of flash memory is addressed via the EADRH SFR (Address 0xC7) and the EADRL SFR (Address 0xC6). Finally, the ECON SFR (Address 0xB9) is an 8-bit control register that can be written to with one of seven flash memory access commands to trigger various read, write, erase, and verify functions. Table 101. Flash SFRs SFR Address Default Bit Addressable Description ECON 0xB9 0x00 No Flash control. FLSHKY 0xBA 0xFF No Flash key. PROTKY 0xBB 0xFF No Flash protection key. EDATA 0xBC 0x00 No Flash data. PROTB0 0xBD 0xFF No Flash W/E Protection 0. PROTB1 0xBE 0xFF No Flash W/E Protection 1. PROTR 0xBF 0xFF No Flash read protection. EADRL 0xC6 0x00 No Flash low byte address. EADRH 0xC7 0x00 No Flash high byte address. Figure 95 demonstrates the steps required for access to the flash memory. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
