ELECTRONICS

FCI Electronics

Manual Part No. 144000-001

Issued: Date (10/24/94)

Page 9 of 10

Rev. 03/08/01 ECR V103118

Revision B

K\DCU\Manuals

4

Reinstall the anvil holder assembly onto the hand tool

and tighten the attaching cap screw.

5

Crimp a terminal to the proper size wire and check the

wire barrel crimp height of the crimped terminal. If

crimp height is not as specified, remove the anvil

holder assembly and turn the adjusting collar an

additional 5 degrees. Then reinstall the anvil holder

assembly and again check the crimp height. Continue

adjusting the crimp height in this manner until the

proper crimp height is achieved.

6

Remove the anvil holder assembly and tighten the

setscrew clockwise in the adjustable tool holder. Then

reinstall the anvil holder assembly and tighten the

attaching cap screw.

VI. PARTS

A. Spare Parts

These are parts that FCI Electronics considers practical for the

user to stock for replacement. Recommended spare parts for the

hand tool are specified in bold type in the parts list for Figure

13.

B. Parts Ordering Information

To obtain replacement parts, contact FCI Electronics, 825

Old Trail Road, Etters, PA 17319; Phone Toll Free 1-800-

237-2374. Provide the description of the part, FCI part

number (if specified), quantity desired, and also the hand

tool model and serial number.

C. Hand Tool Repair Policy

FCI Electronics charges a standard rate to repair any hand

tool not under warranty. Phone Toll Free 1-800-237-2374

to obtain a Return Material Authorization number (RMA),

shipping instructions and the current cost of repair. FCI will

repair the hand tool and return it to you by the fastest means

possible.

Parts List for Figure 13, HT-0102 Hand Tool Parts

Index

no.

Part No.

Description

Quantity

1

A-857-5

CRIMPER HOLDER

1

2*

104964-1

TONKER

2

3*

108175-1

INSULATION BARREL CRIMPER 22-32 GAUGE WIRE

1

4*

108176-1

WIRE BARREL CRIMPER 22-32 GAUGE WIRE

1

5

A-1153

TONKER SPRING

2

6

A-1155

GUIDE SPRING

2

7

915305-224

SHCS, 4-40 NF X

8

8

104963-1

SPRING RETAINER

1

9

915305-205

SHCS, 6-40 NF X

2

10

915305-559

SHSS(SET SCREW) 2-56 NC X 1/8” LONG

2

11

102466-1

ANVIL HOLDER

1

12*

108178-1

INSULATION BARREL ANVIL, SIDE “A”, 28-32 G WIRE

1

13*

108178-2

INSULATION BARREL ANVIL, SIDE “B”, 22-26 G WIRE

1

14*

108177-1

WIRE BARREL ANVIL, SIDE “A”, 28-32 G WIRE

1

15*

108177-2

WIRE BARREL ANVIL, SIDE “B”, 22-26 G WIRE

1

16

102470-1

TERMINAL HOLDER SPRING, 0.65” LONG

2

17

147070-1

TERMINAL HOLDER

1

18

900066-001

O-RING, 0.070” I.D., 01-004

2

19

102468-2

GUIDE PIN

2

20

144547-001

GUIDE RAIL

2

21

147071-1

TERMINAL CLAMP

1

22

147072-1

QUILL PUNCH

1

23

102470-2

PUNCH SPRING, 0.300” LONG

1

24

150564-1

COLLAR. NYLON

1

*Recommended Spare Parts

PDM: Rev:B

Released

STATUS:

Printed: Dec 20, 2002