28F010 datasheet(7/30 Pages) INTEL

7 / 30 page

28F010

Table 2 28F010 Bus Operations

Mode

VPP(1)

DQ0–DQ7

Read

VPPL

VIL

VIH

Data Out

Output Disable

VPPL

VIL

VIH

Tri-State

READ-ONLY

Standby

VPPL

VIH

Tri-State

Intelligent Identifier (Mfr)(2)

VPPL

VIL

VID(3)

VIL

VIH

Data e 89H

Intelligent Identifier (Device)(2)

VPPL

VIH VID(3)

VIL

VIH

Data e B4H

Read

VPPH

VIL

VIH

Data Out(4)

READWRITE

Output Disable

VPPH

VIL

VIH

Tri-State

Standby(5)

VPPH

VIH

Tri-State

Write

VPPH

VIL

VIH

VIL

Data In(6)

NOTES

1 Refer to DC Characteristics When VPP e VPPL memory contents can be read but not written or erased

2 Manufacturer and device codes may also be accessed via a command register write sequence Refer to Table 3 All other

addresses low

3 VID is the Intelligent Identifier high voltage Refer to DC Characteristics

4 Read operations with VPP e VPPH may access array data or the Intelligent Identifier codes

5 With VPP at high voltage the standby current equals ICC a IPP (standby)

6 Refer to Table 3 for valid Data-In during a write operation

7 X can be VIL or VIH

tents of the register default to the read command

making the 28F010 a read-only memory In this

mode the memory contents cannot be altered

Or the system designer may choose to ‘‘hardwire’’

VPP making the high voltage supply constantly

available In this case all Command Register func-

tions are inhibited whenever VCC is below the write

lockout voltage VLKO (See Power UpDown Protec-

tion) The 28F010 is designed to accommodate ei-

ther design practice and to encourage optimization

of the processor-memory interface

The two-step programerase write sequence to the

Command Register provides additional software

write protections

BUS OPERATIONS

Read

The 28F010 has two control functions both of which

must be logically active to obtain data at the out-

puts Chip-Enable (CE ) is the power control and

should be used for device selection Output-Enable

(OE ) is the output control and should be used to

gate data from the output pins independent of de-

vice selection Refer to AC read timing waveforms

When VPP is high (VPPH) the read operation can be

used to access array data to output the Intelligent

Identifier codes and to access data for program

erase verification When VPP is low (VPPL) the read

operation can only access the array data

Output Disable

With OE

at a logic-high level (VIH) output from the

device is disabled Output pins are placed in a high-

impedance state

Standby

With CE

at a logic-high level the standby opera-

tion disables most of the 28F010’s circuitry and sub-

stantially reduces device power consumption The

outputs are placed in a high-impedance state inde-

pendent of the OE

signal If the 28F010 is dese-

lected during erasure programming or program

erase verification the device draws active current

until the operation is terminated

Intelligent Identifier Operation

The Intelligent Identifier operation outputs the manu-

facturer code (89H) and device code (B4H) Pro-

gramming equipment automatically matches the de-

vice with its proper erase and programming algo-

rithms

28F010 датащи(PDF) 7 Page - Intel Corporation

28F010 датащи(HTML) 7 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

датащи скачать

ссылки URL