 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
TAS5729MD датащи(PDF) 3 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
TAS5729MD датащи(HTML) 3 Page - Texas Instruments |
|
|
3 / 59 page  Thermal Pad 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 PGND SPK_OUTA BSTRPA PVDD TEST1 TEST2 DR_INA DR_OUTA DR_OUTB DR_INB DRVSS DR_CN DR_CP DRVDD PLL_GND PLL_FLTM PLL_FLTP ANA_REG1 AVDD ADR / SPK_FAULT MCLK OSC_RES OSC_GND DIG_REG SPK_OUTB BSTRPB BSTRPC SPK_OUTC PGND SPK_OUTD BSTRPD PVDD GVDD_REG DR_SDI SSTIMER ANA_REG2 AGND DGND DVDD TEST3 RST NC SCL SDA SDIN SCLK LRCLK PDN TAS5729MD www.ti.com SLOS836A – MAY 2013 – REVISED JUNE 2013 PINOUT AND PIN DESCRIPTIONS TSSOP PACKAGE DCA-48 (TOP VIEW) TAS5729MD Pin Out PIN TYPE(1) TERMINATION DESCRIPTION NAME NO. Dual function terminal which sets the LSB of the 7-bit I²C address to 0 if pulled to GND, 1 if pulled to DVDD. If configured to be a fault output via the System Control ADR/SPK_FAULT 20 DI/DO - Register 2 (0x05), this terminal is pulled low when an internal fault with the speaker amplifier occurs. A pull-up or pull-down resistor is required, as is shown in the Typical Application Circuit Diagrams. AGND 36 P - Ground for analog circuitry(2) AVDD 19 P - Power supply for internal analog circuitry Linear voltage regulator output derived from AVDD supply which is used for internal ANA_REG1 18 P - analog circuitry. Nominal 1.8 V output.(3) Linear voltage regulator output derived from AVDD supply which is used for internal ANA_REG2 37 P - analog circuitry. Nominal 3.3 V output.(3) Connection points for the bootstrap capacitors, which are used to create a power BSTRPx 3, 42, 46, 47 P - supply for the high-side gate drive of the device DGND 35 P - Ground for digital circuitry(2) Linear voltage regulator output derived from DVDD supply which is used for internal DIG_REG 24 P - digital circuitry(3) Negative terminal for capacitor connection used in headphone amplifier and line DR_CN 12 P - driver charge pump Positive terminal for capacitor connection used in headphone amplifier and line DR_CP 13 P - driver charge pump DR_INx 7, 10 AI - Input for channel A or B of headphone amplifier or line driver DR_OUTx 8, 9 AO - Output for channel A or B of headphone amplifier or line driver DR_SDI 39 DI - Places the headphone amplifier/line driver in shutdown when pulled low. Negative supply generated by charge pump for ground centered headphone and DRVSS 11 P - line driver output DRVDD 14 P - Power supply for internal headphone and line driver circuitry (1) TYPE: AI = Analog input, AO = Analog output, DI = Digital Input, DO = Digital Output, P = Power, G = Ground (0V) (2) This terminal should be connected to the system ground (3) This terminal is provided as a connection point for filtering capacitors for this supply and must not be used to power any external circuitry. Copyright © 2013, Texas Instruments Incorporated 3 Product Folder Links: TAS5729MD |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
