CS5360 datasheet(12/22 Pages) CIRRUS

12 / 22 page

CS5360

DS280PP2

taken high during normal operation, the current

value of the dc offset register is frozen and this dc

offset will continue to be subtracted from the con-

version result. This feature makes it possible to per-

form a system calibration by:

1) removing the signal source (or grounding the

input signal) at the input to the subsystem con-

taining the CS5360,

2) running the CS5360 with the HP DEFEAT pin

low (high pass filter enabled) until the filter set-

tles (approximately 1 second), and

3) taking the HP DEFEAT pin high, disabling the

high pass filter and freezing the stored dc off-

set.

A system calibration performed in this way will

eliminate offsets anywhere in the signal path be-

tween the calibration point and the CS5360.

The characteristics of the first-order high pass filter

are outlined below for an output sample rate of

48 kHz. This filter response scales linearly with

sample rate.

Frequency response: -3 dB @ 0.9 Hz

-0.01 dB @ 20 Hz

Phase deviation:

2.6 degrees @ 20 Hz

Passband ripple:

None

4. INPUT LEVEL MONITORING

The CS5360 includes independent Peak Input Lev-

el Monitoring for each channel. The analog-to-dig-

ital converter continually monitors the peak digital

signal for both channels, prior to the digital limiter,

and records these values in the Active registers.

This information can be transferred to the Output

registers by a high to low transition on the Peak Up-

date pin (PU) which will also reset the Active reg-

ister. The Active register contains the peak signal

level since the previous peak update request.

The 8-bit contents of the output registers are avail-

able in all interface modes and are present in the

data block as shown in Figure 7. The monitoring

function can be formatted to indicate either High

Resolution Mode or Bar Graph Mode. The moni-

toring function is determined on power-up by the

presence of a 47 k

Ω pull-down resistor on

FRAME. The addition of a 47 k

Ω pull-down resis-

tor on the FRAME pin sets the monitoring function

to the Bar Graph mode.

4.1

High Resolution Mode

Bits P7-P0 indicate the peak input level since the

previous peak update (or low transition on the Peak

Update pin). If the full scale input level is exceeded

(Bit P7 high), bits P5-P0 represent the peak value

up to 3 dB above full-scale in 1 dB steps. If the

ADC input level is less than full-scale, bits P5-P0

represent the peak value from -60 dB to 0 dB of full

scale in 1 dB steps. The PSL outputs are accurate to

within 0.25 dB. Bit P6 provides a coarse means of

determining an ADC input idle condition. Bit P7

indicates an ADC overflow condition, if the ADC

input level is greater than full-scale.

P7 - Overrange

0 - Analog input less than full-scale level

1 - Analog input greater than full-scale

P6 - Idle channel

0 - Analog input >-60 dB from full-scale

1 - Analog input <-60 dB from full-scale

P5 to P0 - Peak Signal Level Bits (1 dB steps)

Inputs <0 dB

P5 - P0

0 dB

000000

-1 dB

000001

-2 dB

000010

-60 dB

111100

Inputs >0 dB

P5 - P0

0 dB

000000

+1 dB

000001

+2 dB

000010

+3 dB

000011

Table 3. Peak Signal Level Bits - High Resolution Mode

CS5360 датащи(PDF) 12 Page - Cirrus Logic

CS5360 датащи(HTML) 12 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

датащи скачать

ссылки URL