| поискавой системы для электроныых деталей |
|
AT25DF641 датащи(PDF) 13 Page - List of Unclassifed Manufacturers |
|
|
|||||||||||||||||||||||||||||
AT25DF641 датащи(HTML) 13 Page - List of Unclassifed Manufacturers |
|
13 / 56 page ![]() AT25DF641 13 3680F–DFLASH–4/10 Figure 7-1. Byte Program SO SI SCK CS MS B MS B 2 3 1 0 0 0 0 0 0 0 1 0 6 7 5 4 10 11 9 8 12 39 37 38 33 36 35 34 31 32 29 30 OP C ODE HIG H-IMP E DANC E A A A A A A A A A MS B D D D D D D D D ADDR E S S B IT S A23-A0 DAT A IN Figure 7-2. Page Program SO SI SCK MS B MS B 2 3 1 0 0 0 0 0 0 0 1 0 6 7 5 4 9 8 39 37 38 33 36 35 34 31 32 29 30 OP C ODE HIG H-IMP E DANC E A A A A A A MS B D D D D D D D D ADDR E S S BITS A23-A0 DATA IN BY TE 1 MS B D D D D D D D D DATA IN BY TE n CS 7.2. Dual-Input Byte/Page Program The Dual-Input Byte/Page Program command is similar to the standard Byte/Page Program command and can be used to program anywhere from a single byte of data up to 256-bytes of data into previously erased memory locations. Unlike the standard Byte/Page Program command, however, the Dual-Input Byte/Page Program command allows two bits of data to be clocked into the device on every clock cycle rather than just one. Before the Dual-Input Byte/Page Program command can be started, the Write Enable command must have been previously issued to the device (see “Write Enable” on page 21) to set the Write Enable Latch (WEL) bit of the Status Register to a logical “1” state. To perform a Dual-Input Byte/Page Program command, an opcode of A2h must be clocked into the device followed by the three address bytes denoting the first byte location of the memory array to begin programming at. After the address bytes have been clocked in, data can then be clocked into the device two bits at a time on both the SOI and SI pins. The data is always input with the MSB of a byte first, and the MSB is always input on the SOI pin. During the first clock cycle, bit seven of the first data byte would be input on the SOI pin while bit six of the same data byte would be input on the SI pin. During the next clock cycle, bits five and four of the first data byte would be input on the SOI and SI pins, respectively. The sequence would continue with each byte of data being input after every four clock cycles. Like the standard Byte/Page Program command, all data clocked into the device is stored in an internal buffer. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |