ADSP-TS101S datasheet(3/48 Pages) AD

3 / 48 page

ADSP-TS101S

Rev. C

Page 3 of 48

May 2009

GENERAL DESCRIPTION

The ADSP-TS101S TigerSHARC

® processor is an ultrahigh per-

formance, Static Superscalar

†processor optimized for large

signal processing tasks and communications infrastructure. The

DSP combines very wide memory widths with dual computa-

tion blocks—supporting 32- and 40-bit floating-point and 8-,

16-, 32-, and 64-bit fixed-point processing—to set a new stan-

dard of performance for digital signal processors. The

TigerSHARC processor’s Static Superscalar architecture lets the

processor execute up to four instructions each cycle, performing

24 fixed-point (16-bit) operations or six floating-point

operations.

Three independent 128-bit-wide internal data buses, each

connecting to one of the three 2M bit memory banks, enable

quad word data, instruction, and I/O accesses and provide

14.4G bytes per second of internal memory bandwidth. Operat-

ing at 300 MHz, the ADSP-TS101S processor’s core has a 3.3 ns

instruction cycle time. Using its single-instruction, multiple-

data (SIMD) features, the ADSP-TS101S can perform 2.4 billion

40-bit MACs or 600 million 80-bit MACs per second. Table 1

and Table 2 show the DSP’s performance benchmarks.

The ADSP-TS101S is code compatible with the other

TigerSHARC processors.

The Functional Block Diagram on Page 1 shows the processor’s

architectural blocks. These blocks include:

• Dual compute blocks, each consisting of an ALU, multi-

plier, 64-bit shifter, and 32-word register file and associated

data alignment buffers (DABs)

•Dual integer ALUs (IALUs), each with its own 31-word

• A program sequencer with instruction alignment buffer

(IAB), branch target buffer (BTB), and interrupt controller

• Three 128-bit internal data buses, each connecting to one

of three 2M bit memory banks

•On-chip SRAM (6M bit)

• An external port that provides the interface to host proces-

sors, multiprocessing space (DSPs), off-chip memory-

mapped peripherals, and external SRAM and SDRAM

• A 14-channel DMA controller

• Four link ports

• Two 64-bit interval timers and timer expired pin

• A 1149.1 IEEE compliant JTAG test access port for on-chip

emulation

Figure 2 shows a typical single-processor system with external

SDRAM. Figure 4 on Page 8 shows a typical multiprocessor

system.

The TigerSHARC processor uses a Static Superscalar architec-

ture. This architecture is superscalar in that the ADSP-TS101S

processor’s core can execute simultaneously from one to four

32-bit instructions encoded in a very large instruction word

(VLIW) instruction line using the DSP’s dual compute blocks.

Because the DSP does not perform instruction reordering at

runtime—the programmer selects which operations will execute

in parallel prior to runtime—the order of instructions is static.

With few exceptions, an instruction line, whether it contains

one, two, three, or four 32-bit instructions, executes with a

throughput of one cycle in an eight-deep processor pipeline.

For optimal DSP program execution, programmers must follow

the DSP’s set of instruction parallelism rules when encoding an

instruction line. In general, the selection of instructions that the

DSP can execute in parallel each cycle depends on the instruc-

tion line resources each instruction requires and on the source

and destination registers used in the instructions. The program-

mer has direct control of three core components—the IALUs,

the compute blocks, and the program sequencer.

† Static Superscalar is a trademark of Analog Devices, Inc.

Table 1. General-Purpose Algorithm Benchmarks

at 300 MHz

Benchmark

Speed

Clock

Cycles

32-bit algorithm, 600 million MACs/s peak performance

1024 point complex FFT (Radix 2)

32.78 μs

9,835

50-tap FIR on 1024 input

91.67 μs

27,500

Single FIR MAC

1.83 ns

0.55

16-bit algorithm, 2.4 billion MACs/s peak performance

256 point complex FFT (Radix 2)

3.67 μs

1,100

50-tap FIR on 1024 input

24.0 μs

7,200

Single FIR MAC

0.47 ns

0.14

Single complex FIR MAC

1.9 ns

0.57

I/O DMA transfer rate

External port

800M bytes/s

n/a

Link ports (each)

250M bytes/s

n/a

Table 2. 3G Wireless Algorithm Benchmarks

Benchmark

Execution

(MIPS)

1 The execution speed is in instruction cycles per second.

Turbo decode

384 kbps data channel

51 MIPS

Viterbi decode

12.2 kbps AMR3 voice channel

0.86 MIPS

Complex correlation

3.84 Mcps4 with a spreading factor of 256

0.27 MIPS

2 This value is for six iterations of the algorithm. For eight iterations of the turbo

decoder, this benchmark is 67 MIPS.

3 Adaptive multi rate (AMR)

4 Megachips per second (Mcps)

ADSP-TS101S датащи(PDF) 3 Page - Analog Devices

ADSP-TS101S датащи(HTML) 3 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

датащи скачать

ссылки URL