| поискавой системы для электроныых деталей |
|
TGP-751 датащи(PDF) 10 Page - List of Unclassifed Manufacturers |
|
|
|||||||||||||||||||||||||||||
TGP-751 датащи(HTML) 10 Page - List of Unclassifed Manufacturers |
|
10 / 19 page ![]() Micropelt - preliminary - Datasheet TE-CORE v2.5 | Page 10 Thermoharvesting Module Micropelt TE-CORE 3. TE-CORE Components and Connectors 3.1 Output and Power Management The TGP output voltage is stepped-up to a maximum voltage of 5.5 V. The harvested energy is buffered in capacitor C3 . A configurable hysteresis control ensures the buffer is full before the TE-CORE’s output is activat- ed, and turned off before the target output voltage is under run or even killing the step-up oscillation. The output voltage is controlled by a configurable compar- ator. 3.1.1 Storage Charge Hysteresis Configuration The comparator (IC2, MICREL MIC833) turns the output ON once the voltage of capacitor C3 reaches Uhigh set by the resistors R4 , R5 and R6 according to Equations 1 below. The output is turned OFF when the voltage of C3 under runs Ulow, so the entire harvested energy is used to recharge the storage capacitor C3. (Eq. 1) (Eq. 2) 3.1.2 Output Voltage Configuration The comparator (IC3,, TI TPS780 Series) controls the configurable constant output voltage of the TE-CORE module (2.4 V by default) as long as the voltage from IC2 is ON. The voltage level is set by the resistors R2 and R3 according to Equation 2 below. (Eq. 3) PCB top view TGP: TGP-751 or TGP-651 X1: Connector for Texas Instrument evaluation board eZ430-RF2500T (PIN 2 - VCC; PIN 5 - GND) C3: Storage capacitor 100 µF C33: Capacitor extension interface PCB bottom view J1, J2: Soldering pads output polarity selection J3: Soldering pad to disconnect TGP from DC-DC booster / power management X2: Regulated DC output; Uout = 2.4 Volt by default C33: Capacitor extension interface (not populated) J4: Soldering pad to disconnect indicator LED D3 P1: Test pad for storage capacitor voltage P2: GND P3: Raw TGP output (disconnect J3 before use) Magnet - Mounting position for permanent magnet ) 3 2 1 ( R R U U FB out Volt UFB 216 . 1 ) 6 5 6 5 4 ( R R R R R U U ref low ) 6 6 5 4 ( R R R R U U ref high Volt U ref 24 . 1 TGP Heatsink Interface TGP Heat Source Interface |
|
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |