DOC7707 datasheet(117/307 Pages) ETC1

117 / 307 page

117

7707F–AVR–11/10

AT90USB82/162

The OCRnx Register is double buffered when using any of the twelve Pulse Width Modulation

(PWM) modes. For the Normal and Clear Timer on Compare (CTC) modes of operation, the

double buffering is disabled. The double buffering synchronizes the update of the OCRnx Com-

pare Register to either TOP or BOTTOM of the counting sequence. The synchronization

prevents the occurrence of odd-length, non-symmetrical PWM pulses, thereby making the out-

put glitch-free.

The OCRnx Register access may seem complex, but this is not case. When the double buffering

is enabled, the CPU has access to the OCRnx Buffer Register, and if double buffering is dis-

abled the CPU will access the OCRnx directly. The content of the OCR1x (Buffer or Compare)

automatically as the TCNT1 and ICR1 Register). Therefore OCR1x is not read via the high byte

temporary register (TEMP). However, it is a good practice to read the low byte first as when

accessing other 16-bit registers. Writing the OCRnx Registers must be done via the TEMP Reg-

ister since the compare of all 16 bits is done continuously. The high byte (OCRnxH) has to be

written first. When the high byte I/O location is written by the CPU, the TEMP Register will be

updated by the value written. Then when the low byte (OCRnxL) is written to the lower eight bits,

the high byte will be copied into the upper 8-bits of either the OCRnx buffer or OCRnx Compare

For more information of how to access the 16-bit registers refer to “Accessing 16-bit Registers”

on page 109.

15.6.1

Force Output Compare

In non-PWM Waveform Generation modes, the match output of the comparator can be forced by

writing a one to the Force Output Compare (FOCnx) bit. Forcing compare match will not set the

OCFnx Flag or reload/clear the timer, but the OCnx pin will be updated as if a real compare

match had occurred (the COMn1:0 bits settings define whether the OCnx pin is set, cleared or

toggled).

15.6.2

Compare Match Blocking by TCNTn Write

All CPU writes to the TCNTn Register will block any compare match that occurs in the next timer

clock cycle, even when the timer is stopped. This feature allows OCRnx to be initialized to the

same value as TCNTn without triggering an interrupt when the Timer/Counter clock is enabled.

15.6.3

Using the Output Compare Unit

Since writing TCNTn in any mode of operation will block all compare matches for one timer clock

cycle, there are risks involved when changing TCNTn when using any of the Output Compare

channels, independent of whether the Timer/Counter is running or not. If the value written to

TCNTn equals the OCRnx value, the compare match will be missed, resulting in incorrect wave-

form generation. Do not write the TCNTn equal to TOP in PWM modes with variable TOP

values. The compare match for the TOP will be ignored and the counter will continue to 0xFFFF.

Similarly, do not write the TCNTn value equal to BOTTOM when the counter is downcounting.

The setup of the OCnx should be performed before setting the Data Direction Register for the

port pin to output. The easiest way of setting the OCnx value is to use the Force Output Com-

pare (FOCnx) strobe bits in Normal mode. The OCnx Register keeps its value even when

changing between Waveform Generation modes.

Be aware that the COMnx1:0 bits are not double buffered together with the compare value.

Changing the COMnx1:0 bits will take effect immediately.

DOC7707 датащи(PDF) 117 Page - List of Unclassifed Manufacturers

DOC7707 датащи(HTML) 117 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL