AD652KPZ datasheet(15/28 Pages) AD

15 / 28 page

AD652

Rev. C | Page 15 of 28

FREQUENCY-TO-VOLTAGE CONVERTER

The AD652 SVFC also works as a frequency-to-voltage

converter. Figure 22 shows the connection diagram for F/V

conversion. In this case, the negative input of the comparator is

fed the input pulses. Either comparator input may be used so

that an input pulse of either polarity may be applied to the F/V.

In Figure 22, the + input is tied to a 1.2 V reference and low-

level TTL pulses are used as the frequency input. The pulse

must be low on the falling edge of the clock. On the subsequent

rising edge, the 1 mA current source is switched to the

integrator summing junction and ramps up the voltage at Pin 4.

Due to the action of the AND gate, the 1 mA current is switched

off after only one clock period. The average current delivered to

the summing junction varies from 0 mA to 0.5 mA; using the

internal 20 kΩ resistor, this results in a full-scale output voltage

of 10 V at Pin 4.

The frequency response of the circuit is determined by the

capacitor; the −3 dB frequency is simply the RC time constant.

A tradeoff exists between ripple and response. If low ripple is

desired, a large value capacitor must be used (1 µF); if fast

response is needed, a small capacitor is used (1 nF minimum).

The op amp can drive a 5 kΩ resistor load to 10 V, using a 15 V

positive power supply. If a large load capacitance (0.01 µF) must

be driven, it is necessary to isolate the load with a 50 Ω resistor

as shown. Because the 50 Ω resistor is 0.25% of the full scale,

and the specified gain error with the 20 kΩ resistor is 0.5%, this

extra resistor only increases the total gain error to 0.75% max.

The circuit shown is unipolar and only a 0 V to +10 V output is

allowed. The integrator op amp is not a general-purpose op

amp. Instead, it has been optimized for simplicity and high

speed. The most significant difference between this amplifier

and a general-purpose op amp is the lack of an integrator (or

level shift) stage.

Consequently, the voltage on the output (Pin 4) must always be

more positive than 1 V below the inputs (Pins 6 and 7). For

example, in the F-to-V conversion mode, the noninverting input

of the op amp (Pin 6) is grounded, which means the output

(Pin 4) cannot go below −1 V. Normal operation of the circuit as

shown never calls for a negative voltage at the output.

A second difference between this op amp and a general-purpose

amplifier is that the output only sinks 1.5 mA to the negative

supply. The only pull-down other than the 1 mA current used

for voltage-to-frequency conversion is a 0.5 mA source. The op

amp sources a great deal of current from the positive supply,

and is internally protected by current limiting. The op amp

output may be driven to within 4 V of the positive supply when

not sourcing external current. When sourcing 10 mA, the out-

put voltage may be driven to within 6 V of the positive supply.

CLOCK

FREQ

VOLTS

OUT

LOADS ON FALLING EDGE OF CK

SHIFTS OUT ON RISING EDGE OF CL

FREQUENCY TO VOLTS CONVERTER

+VS

–VS

ONE

SHOT

AND

"D"

FLOP

QCK

1mA

20k

Ω

0.01

µF

Ω

AD652

SYNCHRONOUS

VOLTAGE-TO-

FREQUENCY

CONVERTER

REFERENCE

CLOCK

FREQ

DIGITAL

GND

1N4148

–

VOUT

Figure 22. Frequency-to-Voltage Converter

AD652KPZ датащи(PDF) 15 Page - Analog Devices

AD652KPZ датащи(HTML) 15 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

датащи скачать

ссылки URL