ADG752 datasheet(4/8 Pages) AD

4 / 8 page

REV. 0

ADG752

–4–

Table I. Truth Table

ADG752 IN

Switch S1

Switch S2

OFF

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily

accumulate on the human body and test equipment and can discharge without detection.

Although the ADG752 features proprietary ESD protection circuitry, permanent damage may

occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD

precautions are recommended to avoid performance degradation or loss of functionality.

WARNING!

ESD SENSITIVE DEVICE

ABSOLUTE MAXIMUM RATINGS

(TA = +25°C unless otherwise noted)

VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +6 V

Analog, Digital Inputs2 . . . . . . . . . . . . –0.3 V to VDD +0.3 V or

30 mA, Whichever Occurs First

Peak Current, S or D . . . . . . . . . . . . . . . . . . . . . . . . . . .100 mA

(Pulsed at 1 ms, 10% Duty Cycle Max)

Continuous Current, S or D . . . . . . . . . . . . . . . . . . . . . 30 mA

Operating Temperature Range

Industrial (B Version) . . . . . . . . . . . . . . . . . –40

°C to +85°C

Storage Temperature Range . . . . . . . . . . . . . –65

°C to +150°C

Power Dissipation . . . . . . . . . . . . . . . . . . . . . (TJ Max–TA)/

θJA

Junction Temperature (TJ Max) . . . . . . . . . . . . . . . . . .+150

°C

µSOIC Package

θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 206°C/W

θJC Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . 44°C/W

SOT-23 Package

θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . 229.6°C/W

θJC Thermal Impedance . . . . . . . . . . . . . . . . . . . . 91.99°C/W

Lead Temperature, Soldering

Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . . +215

°C

Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+220

°C

NOTES

1Stresses above those listed under Absolute Maximum Ratings may cause perma-

nent damage to the device. This is a stress rating only; functional operation of the

device at these or any other conditions above those listed in the operational sections

of this specification is not implied. Exposure to absolute maximum rating condi-

tions for extended periods may affect device reliability. Only one absolute maxi-

mum rating may be applied at any one time.

2Overvoltages at IN, S or D will be clamped by internal diodes. Current should be

limited to the maximum ratings given.

ORDERING GUIDE

Model

Temperature Range

Brand*

Package Descriptions

Package Options

ADG752BRM

–40

°C to +85°C

SEB

µSOIC

RM-8

ADG752BRT

–40

°C to +85°C

SEB

SOT-23

RT-6

*Brand on these packages is limited to three characters due to space constraints.

TERMINOLOGY

VDD

Most positive power supply potential.

GND

Ground (0 V) reference.

Source terminal. May be an input or output.

Drain terminal. May be an input or output.

Logic control input.

RON

Ohmic resistance between D and S.

∆RON

On resistance match between channels, i.e.,

RONmax–RONmin.

RFLAT(ON)

Flatness is defined as the difference between

the maximum and minimum value of on resis-

tance as measured over the specified analog

signal range.

IS (OFF)

Source leakage current with the switch “OFF.”

ID, IS (ON)

Channel leakage current with the switch “ON.”

VD (VS)

Analog voltage on terminals D and S.

CS (OFF)

“OFF” switch source capacitance.

CD, CS (ON)

“ON” switch capacitance.

tON

Delay between applying the digital control

input and the output switching on. See Test

Circuit 4.

tOFF

Delay between applying the digital control

input and the output switching off.

“OFF” time or “ON” time measured between

the 90% points of both switches, when switch-

ing from one address state to another.

Off Isolation

A measure of unwanted signal coupling

through an “OFF” switch.

Crosstalk

A measure of unwanted signal that is coupled

through from one channel to another as a

result of parasitic capacitance.

Bandwidth

The frequency at which the output is attenu-

ated by –3 dBs.

On Response

The frequency response of the “ON” switch.

Insertion Loss

Loss due to the ON resistance of the switch.

VINL

Maximum input voltage for Logic “0.”

VINH

Minimum input voltage for Logic “1.”

IINL(IINH)

Input current of the digital input.

IDD

Positive supply current.

PIN CONFIGURATIONS

6-Lead SOT-23

(RT-6)

TOP VIEW

(Not to Scale)

ADG752

VDD

GND

8-Lead

SOIC

(RM-8)

TOP VIEW

(Not to Scale)

NC = NO CONNECT

ADG752

VDD

GND

ADG752 датащи(PDF) 4 Page - Analog Devices

ADG752 датащи(HTML) 4 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8

датащи скачать

ссылки URL