AD7701

REV. D

–4–

ORDERING GUIDE

Temperature

Linearity

Package

Model

Range

Error (% FSR) Options*

AD7701AN

–40

°C to +85°C

0.003

N-20

AD7701BN

–40

°C to +85°C

0.0015

N-20

AD7701AR

–40

°C to +85°C

0.003

R-20

AD7701BR

–40

°C to +85°C

0.0015

R-20

AD7701ARS

–40

°C to +85°C

0.003

RS-28

AD7701AQ

–40

°C to +85°C

0.003

Q-20

AD7701BQ

–40

°C to +85°C

0.0015

Q-20

AD7701SQ

–55

°C to +125°C 0.003

Q-20

AD7701TQ

–55

°C to +125°C 0.0015

Q-20

NOTES

*N = Plastic DIP; Q = Cerdip; R = SOIC; RS = SSOP.

PIN FUNCTION DESCRIPTION

Pin

Mnemonic

Description

1

MODE

Selects the Serial Interface Mode. If MODE is tied to –5 V, the AD7701 will operate in the asynchronous

communications (ac) mode. The SCLK pin is configured as an input, and data is transmitted in two bytes,

each with one start bit and two stop bits. If MODE is tied to DGND, the synchronous external clocking

(SEC) mode is selected. SCLK is configured as an input, and the output appears without formatting, the

MSB coming first. If MODE is tied to +5 V, the AD7701 operates in the synchronous self-clocking (SSC)

2

CLKOUT

Clock Output to generate an Internal Master Clock by connecting a crystal between CLKOUT and CLKIN.

If an external clock is used, CLKOUT is not connected.

3

CLKIN

Clock Input for External Clock.

4, 17

SC1, SC2

System Calibration Pins. The state of these pins, when CAL is taken high, determines the type of calibration

performed.

5

DGND

Digital Ground. Ground reference for all digital signals.

Digital Negative Supply, –5 V nominal.

Analog Negative Supply, –5 V nominal.

8

AGND

Analog Ground. Ground reference for all analog signals.

Analog Input.

10

Voltage Reference Input, +2.5 V nominal. This determines the value of positive full-scale in the unipolar

mode and of both positive and negative full-scale in the bipolar mode.

11

SLEEP

Sleep mode pin. When this pin is taken low, the AD7701 goes into a low-power mode with typically 10

µW

power consumption.

12

BP/UP

Bipolar/Unipolar Mode Pin. When this pin is low, the AD7701 is configured for a unipolar input range going

±V

13

CAL

Calibration Mode Pin. When CAL is taken high for more than 4 cycles, the AD7701 is reset and performs a

calibration cycle when CAL is brought low again. The CAL pin can also be used as a strobe to synchronize

the operation of several AD7701s.

14

Analog Positive Supply, +5 V nominal.

15

Digital Positive Supply, +5 V nominal.

16

CS

Chip Select Input. When CS is brought low, the AD7701 will begin to transmit serial data in a format deter-

mined by the state of the MODE pin.

18

DRDY

Data Ready output. DRDY is low when valid data is available in the output register. It goes high after transmission

of a word is completed. It also goes high for four clock cycles when a new data word is being loaded into the out-

put register, to indicate that valid data is not available, irrespective of whether data transmission is complete or not.

19

SCLK

Serial Clock Input/Output. The SCLK pin in configured as an input or output, dependent on the type of se-

rial data transmission that has been selected by the MODE pin. When configured as an output in the syn-

20

SDATA

Serial Data Output. The AD7701’s output data is available at this pin as a 16-bit serial word. The transmis-

sion format is determined by the state of the MODE pin.

DIP, Cerdip, SOIC

MODE

SC1

DGND

CLKOUT

CLKIN

AGND

SDATA

SCLK

SC2

CAL

DRDY

CS

BP/UP

SLEEP

TOP VIEW

(Not to Scale)

AD7701

1

2

3

4

5

6

7

8

9

10

14

13

12

11

20

19

18

17

16

15

SSOP

MODE

SC1

DGND

CLKOUT

CLKIN

AGND

SDATA

SCLK

SC2

CAL

DRDY

CS

BP/UP

SLEEP

TOP VIEW

(Not to Scale)

AD7701

1

2

3

4

5

6

7

8

9

10

14

13

12

11

20

19

18

17

16

15

21

22

23

24

25

26

27

28

NC

NC

NC

NC

NC

NC

NC

NC

NC = NO CONNECT

PIN CONFIGURATIONS