ADP1879ACPZ-0.6-R7 datasheet(21/40 Pages) AD

21 / 40 page

Data Sheet

ADP1878/ADP1879

Rev. A | Page 21 of 40

Figure 73. Idle Mode Entry Sequence Due to Current-Limit Violation

HICCUP MODE DURING SHORT CIRCUIT

A current-limit violation occurs when the current across the

source and drain of the low-side MOSFET exceeds the current-

limit setpoint. When 32 current-limit violations are detected,

the controller enters idle mode and turns off the MOSFETs for

6 ms, allowing the converter to cool down. Then, the controller

reestablishes soft start and begins to cause the output to ramp

up again (see Figure 73). While the output ramps up, the current

sense amplifier output is monitored to determine if the violation is

still present. If it is still present, the idle event occurs again, followed

by the full chip, power-down sequence. This cycle continues

until the violation no longer exists. If the violation disappears,

the converter is allowed to switch normally, maintaining

regulation.

SYNCHRONOUS RECTIFIER

The ADP1878/ADP1879 employ internal MOSFET drivers for

the external high- and low-side MOSFETs. The low-side

synchronous rectifier not only improves overall conduction

efficiency, but it also ensures proper charging of the bootstrap

capacitor located at the high-side driver input. This is beneficial

during startup to provide sufficient drive signal to the external

high-side MOSFET and to attain fast turn-on response, which is

essential for minimizing switching losses. The integrated high-

and low-side MOSFET drivers operate in complementary

fashion with built-in anti cross conduction circuitry to prevent

unwanted shoot through current that may potentially damage the

MOSFETs or reduce efficiency because of excessive power loss.

ADP1879 POWER SAVING MODE (PSM)

A power saving mode is provided in the ADP1879. The ADP1879

operates in the discontinuous conduction mode (DCM) and

pulse skips at light to medium load currents. The controller outputs

pulses as necessary to maintain output regulation. Unlike the

continuous conduction mode (CCM), DCM operation prevents

negative current, thus allowing improved system efficiency at

light loads. Current in the reverse direction through this pathway,

however, results in power dissipation and, therefore, a decrease in

efficiency.

Figure 74. Discontinuous Mode of Operation (DCM)

To minimize the chance of negative inductor current buildup,

an on-board zero-cross comparator turns off all high- and low-

side switching activities when the inductor current approaches

the zero current line, causing the system to enter idle mode,

where the high- and low-side MOSFETs are turned off. To ensure

idle mode entry, a 10 mV offset, connected in series at the SW

node, is implemented (see Figure 75).

Figure 75. Zero-Cross Comparator with 10 mV of Offset

As soon as the forward current through the low-side MOSFET

decreases to a level where

10 mV = IQ2 × RON(Q2)

the zero-cross comparator (or IREV comparator) emits a signal to

turn off the low-side MOSFET. From this point, the slope of the

inductor current ramping down becomes steeper (see Figure 76)

as the body diode of the low-side MOSFET begins to conduct

current and continues conducting current until the remaining

energy stored in the inductor has been depleted.

CLIM

ZERO

CURRENT

REPEATED CURRENT-LIMIT

VIOLATION DETECTED

A PREDETERMINED NUMBER

OF PULSES IS COUNTED TO

ALLOW THE CONVERTER

TO COOL DOWN

SOFT START IS

REINITIALIZED TO

MONITOR IF THE

VIOLATION

STILL EXISTS

HS AND LS ARE OFF

OR IN IDLE MODE

ILOAD

AS THE INDUCTOR

CURRENT APPROACHES

ZERO CURRENT, THE STATE

MACHINE TURNS OFF THE

LOWER-SIDE MOSFET.

tON

tOFF

10mV

ZERO-CROSS

COMPARATOR

IQ2

ADP1879ACPZ-0.6-R7 датащи(PDF) 21 Page - Analog Devices

ADP1879ACPZ-0.6-R7 датащи(HTML) 21 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

датащи скачать

ссылки URL