AD9653 datasheet(31/40 Pages) AD

31 / 40 page

Data Sheet

AD9653

Rev. 0 | Page 31 of 40

SERIAL PORT INTERFACE (SPI)

The AD9653 serial port interface (SPI) allows the user to configure

the converter for specific functions or operations through a

structured register space provided inside the ADC. The SPI

offers the user added flexibility and customization, depending on

the application. Addresses are accessed via the serial port and

can be written to or read from via the port. Memory is organized

into bytes that can be further divided into fields, which are docu-

mented in the Memory Map section. For detailed operational

information, see the AN-877 Application Note, Interfacing to

High Speed ADCs via SPI.

CONFIGURATION USING THE SPI

Three pins define the SPI of this ADC: the SCLK pin, the SDIO

pin, and the CSB pin (see Table 17). The SCLK (a serial clock) is

used to synchronize the read and write data presented from and

to the ADC. The SDIO (serial data input/output) is a dual-

purpose pin that allows data to be sent to and read from the

internal ADC memory map registers. The CSB (chip select bar)

is an active low control that enables or disables the read and

write cycles.

Table 17. Serial Port Interface Pins

Function

SCLK

Serial clock. The serial shift clock input, which is used to

synchronize serial interface reads and writes.

SDIO

Serial data input/output. A dual-purpose pin that

typically serves as an input or an output, depending on

the instruction being sent and the relative position in the

timing frame.

CSB

Chip select bar. An active low control that gates the read

and write cycles.

The falling edge of the CSB, in conjunction with the rising edge

of the SCLK, determines the start of the framing. An example of

the serial timing and its definitions can be found in Figure 75

and Table 7.

Other modes involving the CSB are available. The CSB can be

held low indefinitely, which permanently enables the device;

this is called streaming. The CSB can stall high between bytes to

allow for additional external timing. When CSB is tied high, SPI

functions are placed in high impedance mode. This mode turns

on any SPI pin secondary functions.

During an instruction phase, a 16-bit instruction is transmitted.

Data follows the instruction phase, and its length is determined

by the W0 and W1 bits.

In addition to word length, the instruction phase determines

whether the serial frame is a read or write operation, allowing

the serial port to be used both to program the chip and to read

the contents of the on-chip memory. The first bit of the first byte in

a multibyte serial data transfer frame indicates whether a read

command or a write command is issued. If the instruction is a

readback operation, performing a readback causes the serial

data input/output (SDIO) pin to change direction from an input to

an output at the appropriate point in the serial frame.

All data is composed of 8-bit words. Data can be sent in MSB-

first mode or in LSB-first mode. MSB-first mode is the default

on power-up and can be changed via the SPI port configuration

see the AN-877 Application Note, Interfacing to High Speed

ADCs via SPI.

Figure 75. Serial Port Interface Timing Diagram

DON’T CARE

SDIO

SCLK

CSB

tDH

tCLK

tDS

R/W

A12

A11

A10

tLOW

tHIGH

AD9653 датащи(PDF) 31 Page - Analog Devices

AD9653 датащи(HTML) 31 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

датащи скачать

ссылки URL