LH28F008SC datasheet(13/38 Pages) SHARP

13 / 38 page

8M (1M × 8) Flash Memory

LH28F008SC

WSMS

ESS

ECLBS

BWSLBS

VPPS

BWSS

DPS

765

SR.7

= WRITE STATE MACHINE STATUS

1 = Ready

0 = Busy

SR.6

= ERASE SUSPEND STATUS

1 = Block Erase Suspended

0 = Block Erase in Progress/Completed

SR.5

= ERASE AND CLEAR LOCK-BIT STATUS

1 = Error in Block Erasure or Clear Lock-Bits

0 = Successful Block Erase or Clear Lock-Bits

SR.4

= BYTE WRITE AND SET LOCK-BIT STATUS

1 = Error in Byte Write or Set Master/Block Lock Bit

0 = Successful Byte Write or Set Master/Block

0 = Lock-Bit

SR.3

= VPP STATUS (VPPS)

1 = VPP Low Detect, Operation Abort

0 = VPP OK

SR.2

= BYTE WRITE SUSPEND STATUS

1 = Byte Write Suspended

0 = Byte Write in Progress/Completed

SR.1

= DEVICE PROTECT STATUS

1 = Master Lock-Bit, Block Lock-Bit and/or

1 = RP

» Lock Detected, Operation Abort

0 = Unlock

SR.0

= RESERVED FOR FUTURE ENHANCEMENTS

NOTES:

1. Check RY

»/BY » or SR.7 to determine block erase, byte

write, or lock-bit configuration completion. SR.6 - SR.0 are

invalid while SR.7 = '0'.

2. If both SR.5 and SR.4 are '1's after a block erase or lock-

bit configuration attempt, an improper command sequence

was entered.

3. SR.3 does not provide a continuous indication of VPP level.

The WSM interrogates and indicates the VPP level only

after Block Erase, Byte Write, Set Block/Master Lock-Bit,

or Clear Block Lock-Bits command sequences. SR.3 is not

guaranteed to report accurate feedback only when

VPP = VPPH1/2/3.

4. SR.1 does not provide a continuous indication of master

and block lock-bit values. The WSM interrogates the master

lock-bit, block lock-bit, and RP

» only after Block Erase, Byte

Write, or Lock-Bit configuration command sequences. It

informs the system, depending on the attempted operation,

if the block lock-bit is set, master lock-bit is set, and/or RP

is not VHH. Reading the block lock and master lock configu-

ration codes after writing the Read identifier Codes com-

mand indicates master and block lock-bit status.

5. SR.0 is reserved for future use and should be masked out

when polling the status register.

OPERATION

MASTER

LOCK-BIT

BLOCK

LOCK-BIT

RP#

EFFECT

Block Erase or

Byte Write

IH or VHH

Block Erase and Byte Write Enabled.

Block is locked. Block Erase and Byte Write Disabled.

Block Lock-Bit Override. Block Erase and Byte Write Enabled.

Set Block

Lock Bit

IH or VHH

Set Block Lock-Bit Enabled.

Master Lock-Bit is Set. Set Block Lock-Bit Disabled.

Master Lock-Bit Override. Set Block Lock-Bit Enabled.

Set Master

Lock-Bit

Set Master Lock-Bit Disabled.

Set Master Lock-Bit Enabled.

Clear Block

Lock-Bits

IH or VHH

Clear Block Lock-Bits Enable.

Master Lock-Bit is Set. Clear Block Lock-Bits Disabled.

Master Lock-Bit Override. Clear Block Lock-Bits Enabled.

Write Protection Alternatives

Status Register Definition

LH28F008SC датащи(PDF) 13 Page - Sharp Corporation

LH28F008SC датащи(HTML) 13 Page - Sharp Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38

датащи скачать

ссылки URL