SC312XDP512F0MPVR datasheet(770/1348 Pages) FREESCALE

770 / 1348 page

Chapter 20 S12X Debug (S12XDBGV3) Module

MC9S12XDP512 Data Sheet, Rev. 2.21

772

Freescale Semiconductor

match condition requires that a valid match for both comparators happens on the same bus cycle. A match

condition on only one comparator is not valid. An aligned word access which straddles the range boundary

will cause a trigger only if the aligned address is inside the range.

20.4.2.3.2

Outside Range (address < CompAC_Addr or address > CompBD_Addr)

In the Outside Range comparator mode, either comparator pair A and B or comparator pair C and D can

be conﬁgured for range comparisons. A single match condition on either of the comparators is recognized

as valid. An aligned word access which straddles the range boundary will cause a trigger only if the aligned

address is outside the range.

Outside range mode in combination with tagged triggers can be used to detect if the opcode fetches are

from an unexpected range. In forced trigger modes the outside range trigger would typically be activated

at any interrupt vector fetch or register access. This can be avoided by setting the upper range limit to

$7FFFFF or lower range limit to $000000 respectively.

When comparing the XGATE address bus in outside range mode, the initial vector fetch as determined by

the vector contained in the XGATE XGVBR register should be taken into consideration. The XGVBR

20.4.3

Trigger Modes

Trigger modes are used as qualiﬁers for a state sequencer change of state. The control logic determines the

trigger mode and provides a trigger to the state sequencer. The individual trigger modes are described in

the following sections.

20.4.3.1

Forced Trigger On Comparator Match

If a forced trigger comparator match occurs, the trigger immediately initiates a transition to the next state

sequencer state whereby the corresponding ﬂags in DBGSR are set. The state control register for the

current state determines the next state for each trigger. Forced triggers are generated as soon as the

matching address appears on the address bus, which in the case of opcode fetches occurs several cycles

before the opcode execution. For this reason a forced trigger of an opcode address precedes a tagged trigger

at the same address by several cycles.

20.4.3.2

Trigger On Comparator Related Taghit

If either a S12XCPU or XGATE taghit occurs a transition to another state sequencer state is initiated and

the corresponding DBGSR ﬂags are set. For a comparator related taghit to occur, the S12XDBG must ﬁrst

generate tags based on comparator matches. When the tagged instruction reaches the execution stage of

the instruction queue a taghit is generated by the S12XCPU/XGATE. The state control register for the

current state determines the next state for each trigger.

20.4.3.3

External Tagging Trigger

In external tagging trigger mode, the TAGLO and TAGHI pins (mapped to device pins) are used to tag an

instruction. This function can be used as another breakpoint source. When the tagged opcode reaches the

SC312XDP512F0MPVR датащи(PDF) 770 Page - Freescale Semiconductor, Inc

SC312XDP512F0MPVR датащи(HTML) 770 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL