PIC12F1822-ISLASHMF datasheet(297/398 Pages) MICROCHIP

297 / 398 page

 2010 Microchip Technology Inc.

Preliminary

DS41413A-page 297

PIC12F/LF1822/16F/LF1823

25.3.2

AUTO-BAUD OVERFLOW

During the course of automatic baud detection, the

ABDOVF bit of the BAUDCON register will be set if the

baud rate counter overflows before the fifth rising edge

is detected on the RX pin. The ABDOVF bit indicates

that the counter has exceeded the maximum count that

can fit in the 16 bits of the SPBRGH:SPBRGL register

pair. After the ABDOVF has been set, the counter con-

tinues to count until the fifth rising edge is detected on

the RX pin. Upon detecting the fifth RX edge, the hard-

ware will set the RCIF interrupt flag and clear the

ABDEN bit of the BAUDCON register. The RCIF flag

can be subsequently cleared by reading the RCREG

can be cleared by software directly.

To terminate the auto-baud process before the RCIF

flag is set, clear the ABDEN bit then clear the ABDOVF

bit of the BAUDCON register. The ABDOVF bit will

remain set if the ABDEN bit is not cleared first.

25.3.3

AUTO-WAKE-UP ON BREAK

During Sleep mode, all clocks to the EUSART are

suspended. Because of this, the Baud Rate Generator

is inactive and a proper character reception cannot be

performed. The Auto-Wake-up feature allows the

controller to wake-up due to activity on the RX/DT line.

This feature is available only in Asynchronous mode.

The Auto-Wake-up feature is enabled by setting the

WUE bit of the BAUDCON register. Once set, the normal

receive sequence on RX/DT is disabled, and the

EUSART remains in an Idle state, monitoring for a

wake-up event independent of the CPU mode. A

wake-up event consists of a high-to-low transition on the

RX/DT line. (This coincides with the start of a Sync Break

or a wake-up signal character for the LIN protocol.)

The EUSART module generates an RCIF interrupt

coincident with the wake-up event. The interrupt is

generated synchronously to the Q clocks in normal CPU

operating modes (Figure 25-7), and asynchronously if

the device is in Sleep mode (Figure 25-8). The interrupt

condition is cleared by reading the RCREG register.

The WUE bit is automatically cleared by the low-to-high

transition on the RX line at the end of the Break. This

signals to the user that the Break event is over. At this

point, the EUSART module is in Idle mode waiting to

receive the next character.

25.3.3.1

Special Considerations

Break Character

To avoid character errors or character fragments during

a wake-up event, the wake-up character must be all

zeros.

When the wake-up is enabled the function works

independent of the low time on the data stream. If the

WUE bit is set and a valid non-zero character is

received, the low time from the Start bit to the first rising

edge will be interpreted as the wake-up event. The

remaining bits in the character will be received as a

fragmented character and subsequent characters can

result in framing or overrun errors.

Therefore, the initial character in the transmission must

be all ‘0’s. This must be 10 or more bit times, 13-bit

times recommended for LIN bus, or any number of bit

times for standard RS-232 devices.

Oscillator Startup Time

Oscillator start-up time must be considered, especially

in applications using oscillators with longer start-up

intervals (i.e., LP, XT or HS/PLL mode). The Sync

Break (or wake-up signal) character must be of

sufficient length, and be followed by a sufficient

interval, to allow enough time for the selected oscillator

to start and provide proper initialization of the EUSART.

WUE Bit

The wake-up event causes a receive interrupt by

setting the RCIF bit. The WUE bit is cleared in

hardware by a rising edge on RX/DT. The interrupt

condition is then cleared in software by reading the

RCREG register and discarding its contents.

To ensure that no actual data is lost, check the RCIDL

bit to verify that a receive operation is not in process

before setting the WUE bit. If a receive operation is not

occurring, the WUE bit may then be set just prior to

entering the Sleep mode.

PIC12F1822-I/MF датащи(PDF) 297 Page - Microchip Technology

PIC12F1822-I/MF датащи(HTML) 297 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL