PIC12F1822-ISLASHMF datasheet(265/398 Pages) MICROCHIP

265 / 398 page

 2010 Microchip Technology Inc.

Preliminary

DS41413A-page 265

PIC12F/LF1822/16F/LF1823

24.6.8

ACKNOWLEDGE SEQUENCE

TIMING

An Acknowledge sequence is enabled by setting the

Acknowledge Sequence Enable bit, ACKEN bit of the

SSP1CON2 register. When this bit is set, the SCL pin is

pulled low and the contents of the Acknowledge data bit

are presented on the SDA pin. If the user wishes to gen-

erate an Acknowledge, then the ACKDT bit should be

cleared. If not, the user should set the ACKDT bit before

starting an Acknowledge sequence. The Baud Rate

Generator then counts for one rollover period (TBRG)

and the SCL pin is deasserted (pulled high). When the

SCL pin is sampled high (clock arbitration), the Baud

Rate Generator counts for TBRG. The SCL pin is then

pulled low. Following this, the ACKEN bit is automatically

cleared, the Baud Rate Generator is turned off and the

MSSP1

module

then

goes

into

Idle

mode

(Figure 24-29).

24.6.8.1

WCOL Status Flag

If the user writes the SSP1BUF when an Acknowledge

sequence is in progress, then WCOL is set and the

contents of the buffer are unchanged (the write doesn’t

occur).

24.6.9

STOP CONDITION TIMING

A Stop bit is asserted on the SDA pin at the end of a

receive/transmit by setting the Stop Sequence Enable

bit, PEN bit of the SSP1CON2 register. At the end of a

receive/transmit, the SCL line is held low after the

falling edge of the ninth clock. When the PEN bit is set,

the master will assert the SDA line low. When the SDA

line is sampled low, the Baud Rate Generator is

reloaded and counts down to ‘0’. When the Baud Rate

Generator times out, the SCL pin will be brought high

and one TBRG (Baud Rate Generator rollover count)

later, the SDA pin will be deasserted. When the SDA

pin is sampled high while SCL is high, the P bit of the

SSP1STAT register is set. A TBRG later, the PEN bit is

cleared and the SSP1IF bit is set (Figure 24-30).

24.6.9.1

WCOL Status Flag

If the user writes the SSP1BUF when a Stop sequence

is in progress, then the WCOL bit is set and the

contents of the buffer are unchanged (the write doesn’t

occur).

FIGURE 24-30:

ACKNOWLEDGE SEQUENCE WAVEFORM

Note: TBRG = one Baud Rate Generator period.

SDA

SCL

SSP1IF set at

Acknowledge sequence starts here,

write to SSP1CON2

ACKEN automatically cleared

Cleared in

TBRG

the end of receive

ACKEN = 1, ACKDT = 0

SSP1IF

software

SSP1IF set at the end

of Acknowledge sequence

Cleared in

software

ACK

PIC12F1822-I/MF датащи(PDF) 265 Page - Microchip Technology

PIC12F1822-I/MF датащи(HTML) 265 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL