PIC12F1822-ISLASHMF datasheet(247/398 Pages) MICROCHIP

247 / 398 page

 2010 Microchip Technology Inc.

Preliminary

DS41413A-page 247

PIC12F/LF1822/16F/LF1823

24.5.3

SLAVE TRANSMISSION

When the R/W bit of the incoming address byte is set

and an address match occurs, the R/W bit of the

SSP1STAT register is set. The received address is

loaded into the SSP1BUF register, and an ACK pulse

is sent by the slave on the ninth bit.

Following the ACK, slave hardware clears the CKP bit

and the SCL pin is held low (see Section 24.5.6

“Clock Stretching” for more detail). By stretching the

clock, the master will be unable to assert another clock

pulse until the slave is done preparing the transmit

data.

The transmit data must be loaded into the SSP1BUF

the SCL pin should be released by setting the CKP bit

of the SSP1CON1 register. The eight data bits are

shifted out on the falling edge of the SCL input. This

ensures that the SDA signal is valid during the SCL

high time.

The ACK pulse from the master-receiver is latched on

the rising edge of the ninth SCL input pulse. This ACK

value is copied to the ACKSTAT bit of the SSP1CON2

transfer is complete. In this case, when the not ACK is

latched by the slave, the slave goes idle and waits for

another occurrence of the Start bit. If the SDA line was

low (ACK), the next transmit data must be loaded into

the SSP1BUF register. Again, the SCL pin must be

released by setting bit CKP.

An MSSP1 interrupt is generated for each data transfer

byte. The SSP1IF bit must be cleared by software and

the SSP1STAT register is used to determine the status

of the byte. The SSP1IF bit is set on the falling edge of

the ninth clock pulse.

24.5.3.1

Slave Mode Bus Collision

A slave receives a Read request and begins shifting

data out on the SDA line. If a bus collision is detected

and the SBCDE bit of the SSP1CON3 register is set,

the BCL1IF bit of the PIRx register is set. Once a bus

collision is detected, the slave goes Idle and waits to be

addressed again. User software can use the BCL1IF bit

to handle a slave bus collision.

24.5.3.2

7-bit Transmission

A master device can transmit a read request to a

slave, and then clock data out of the slave. The list

below outlines what software for a slave will need to

accomplish

standard

transmission.

Figure 24-17 can be used as a reference to this list.

Master sends a Start condition on SDA and

SCL.

S bit of SSP1STAT is set; SSP1IF is set if inter-

rupt-on-Start detect is enabled.

Matching address with R/W bit set is received by

the Slave setting SSP1IF bit.

Slave hardware generates an ACK and sets

SSP1IF.

SSP1IF bit is cleared by user.

Software reads the received address from

SSP1BUF, clearing BF.

R/W is set so CKP was automatically cleared

after the ACK.

The slave software loads the transmit data into

SSP1BUF.

CKP bit is set releasing SCL, allowing the mas-

ter to clock the data out of the slave.

10. SSP1IF is set after the ACK response from the

master is loaded into the ACKSTAT register.

11. SSP1IF bit is cleared.

12. The slave software checks the ACKSTAT bit to

see if the master wants to clock out more data.

13. Steps 9-13 are repeated for each transmitted

byte.

14. If the master sends a not ACK; the clock is not

held, but SSP1IF is still set.

15. The master sends a Restart condition or a Stop.

16. The slave is no longer addressed.

Note 1: If the master ACKs the clock will be

stretched.

2: ACKSTAT is the only bit updated on the

rising edge of SCL (9th) rather than the

falling.

PIC12F1822-I/MF датащи(PDF) 247 Page - Microchip Technology

PIC12F1822-I/MF датащи(HTML) 247 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL