ATmega325P datasheet(257/364 Pages) ATMEL

257 / 364 page

257

8023F–AVR–07/09

ATmega325P/3250P

24.4

Read-While-Write and No Read-While-Write Flash Sections

Whether the CPU supports Read-While-Write or if the CPU is halted during a Boot Loader soft-

ware update is dependent on which address that is being programmed. In addition to the two

sections that are configurable by the BOOTSZ Fuses as described above, the Flash is also

divided into two fixed sections, the Read-While-Write (RWW) section and the No Read-While-

Write (NRWW) section. The limit between the RWW- and NRWW sections is given in Table 24-

7 on page 268 and Figure 24-2 on page 259. The main difference between the two sections is:

• When erasing or writing a page located inside the RWW section, the NRWW section can be

read during the operation.

• When erasing or writing a page located inside the NRWW section, the CPU is halted during the

entire operation.

Note that the user software can never read any code that is located inside the RWW section dur-

ing a Boot Loader software operation. The syntax “Read-While-Write section” refers to which

section that is being programmed (erased or written), not which section that actually is being

read during a Boot Loader software update.

24.4.1

RWW – Read-While-Write Section

If a Boot Loader software update is programming a page inside the RWW section, it is possible

to read code from the Flash, but only code that is located in the NRWW section. During an on-

going programming, the software must ensure that the RWW section never is being read. If the

user software is trying to read code that is located inside the RWW section (i.e., by a

call/jmp/lpm or an interrupt) during programming, the software might end up in an unknown

state. To avoid this, the interrupts should either be disabled or moved to the Boot Loader sec-

tion. The Boot Loader section is always located in the NRWW section. The RWW Section Busy

bit (RWWSB) in the Store Program Memory Control and Status Register (SPMCSR) will be read

as logical one as long as the RWW section is blocked for reading. After a programming is com-

pleted, the RWWSB must be cleared by software before reading code located in the RWW

section. See Section “24.9.1” on page 269. for details on how to clear RWWSB.

24.4.2

NRWW – No Read-While-Write Section

The code located in the NRWW section can be read when the Boot Loader software is updating

a page in the RWW section. When the Boot Loader code updates the NRWW section, the CPU

is halted during the entire Page Erase or Page Write operation.

Table 24-1.

Read-While-Write Features

Which Section does the Z-pointer

Address During the Programming?

Which Section Can

be Read During

Programming?

Is the CPU

Halted?

Read-While-Write

Supported?

RWW Section

NRWW Section

Yes

NRWW Section

None

Yes

ATmega325P датащи(PDF) 257 Page - ATMEL Corporation

ATmega325P датащи(HTML) 257 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL