ATmega16M1 datasheet(55/365 Pages) ATMEL

55 / 365 page

7647F–AVR–04/09

ATmega16/32/64/M1/C1

7.4.1

Watchdog Timer Control Register - WDTCSR

• Bit 7 - WDIF: Watchdog Interrupt Flag

This bit is set when a time-out occurs in the Watchdog Timer and the Watchdog Timer is config-

ured for interrupt. WDIF is cleared by hardware when executing the corresponding interrupt

handling vector. Alternatively, WDIF is cleared by writing a logic one to the flag. When the I-bit in

SREG and WDIE are set, the Watchdog Time-out Interrupt is executed.

• Bit 6 - WDIE: Watchdog Interrupt Enable

When this bit is written to one and the I-bit in the Status Register is set, the Watchdog Interrupt is

enabled. If WDE is cleared in combination with this setting, the Watchdog Timer is in Interrupt

Mode, and the corresponding interrupt is executed if time-out in the Watchdog Timer occurs.

If WDE is set, the Watchdog Timer is in Interrupt and System Reset Mode. The first time-out in

the Watchdog Timer will set WDIF. Executing the corresponding interrupt vector will clear WDIE

and WDIF automatically by hardware (the Watchdog goes to System Reset Mode). This is use-

ful for keeping the Watchdog Timer security while using the interrupt. To stay in Interrupt and

System Reset Mode, WDIE must be set after each interrupt. This should however not be done

within the interrupt service routine itself, as this might compromise the safety-function of the

Watchdog System Reset mode. If the interrupt is not executed before the next time-out, a Sys-

tem Reset will be applied.

Note:

1. For the WDTON Fuse “1” means unprogrammed while “0” means programmed.

• Bit 4 - WDCE: Watchdog Change Enable

This bit is used in timed sequences for changing WDE and prescaler bits. To clear the WDE bit,

and/or change the prescaler bits, WDCE must be set.

Once written to one, hardware will clear WDCE after four clock cycles.

• Bit 3 - WDE: Watchdog System Reset Enable

WDE is overridden by WDRF in MCUSR. This means that WDE is always set when WDRF is

set. To clear WDE, WDRF must be cleared first. This feature ensures multiple resets during con-

ditions causing failure, and a safe start-up after the failure.

• Bit 5, 2..0 - WDP3..0: Watchdog Timer Prescaler 3, 2, 1 and 0

The WDP3..0 bits determine the Watchdog Timer prescaling when the Watchdog Timer is run-

ning. The different prescaling values and their corresponding time-out periods are shown in

Table 7-6 on page 56.

Bit

76543210

WDIF

WDIE

WDP3

WDCE

WDE

WDP2

WDP1

WDP0

WDTCSR

Read/Write

R/W

Initial Value

0000

000

Table 7-5.

Watchdog Timer Configuration

WDTON

(1)

WDE

WDIE

Mode

Action on Time-out

Stopped

None

Interrupt Mode

Interrupt

System Reset Mode

Reset

Interrupt and System Reset

Mode

Interrupt, then go to System

Reset Mode

System Reset Mode

Reset

ATmega16M1 датащи(PDF) 55 Page - ATMEL Corporation

ATmega16M1 датащи(HTML) 55 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL