ATmega16M1 datasheet(37/365 Pages) ATMEL

37 / 365 page

7647F–AVR–04/09

ATmega16/32/64/M1/C1

When this clock source is selected, start-up times are determined by the SUT Fuses as shown in

Table 5-9.

When applying an external clock, it is required to avoid sudden changes in the applied clock fre-

quency to ensure stable operation of the MCU. A variation in frequency of more than 2% from

one clock cycle to the next can lead to unpredictable behavior. It is required to ensure that the

MCU is kept in Reset during such changes in the clock frequency.

Note that the System Clock Prescaler can be used to implement run-time changes of the internal

clock frequency while still ensuring stable operation. Refer to “System Clock Prescaler” on page

37 for details.

5.9

Clock Output Buffer

When the CKOUT Fuse is programmed, the system Clock will be output on CLKO. This mode is

suitable when chip clock is used to drive other circuits on the system. The clock will be output

also during reset and the normal operation of I/O pin will be overridden when the fuse is pro-

grammed. Any clock source, including internal RC Oscillator, can be selected when CLKO

serves as clock output. If the System Clock Prescaler is used, it is the divided system clock that

is output (CKOUT Fuse programmed).

5.10

System Clock Prescaler

The ATmega16/32/64/M1/C1 system clock can be divided by setting the Clock Prescale Regis-

ter – CLKPR. This feature can be used to decrease power consumption when the requirement

for processing power is low. This can be used with all clock source options, and it will affect the

clock frequency of the CPU and all synchronous peripherals. clk

I/O, clkADC, clkCPU, and clkFLASH

are divided by a factor as shown in Table 5-10.

When switching between prescaler settings, the System Clock Prescaler ensures that no

glitches occurs in the clock system. It also ensures that no intermediate frequency is higher than

neither the clock frequency corresponding to the previous setting, nor the clock frequency corre-

sponding to the new setting. The ripple counter that implements the prescaler runs at the

frequency of the undivided clock, which may be faster than the CPU's clock frequency. Hence, it

is not possible to determine the state of the prescaler - even if it were readable, and the exact

time it takes to switch from one clock division to the other cannot be exactly predicted. From the

time the CLKPS values are written, it takes between T1 + T2 and T1 + 2 * T2 before the new

clock frequency is active. In this interval, 2 active clock edges are produced. Here, T1 is the pre-

vious clock period, and T2 is the period corresponding to the new prescaler setting.

Table 5-9.

Start-up Times for the External Clock Selection

SUT1..0

Start-up Time from

Power-down and Power-save

Additional Delay from

Reset (V

CC = 5.0V)

Recommended Usage

6 CK

14CK

BOD enabled

6 CK

14CK + 4.1 ms

Fast rising power

6 CK

14CK + 65 ms

Slowly rising power

Reserved

ATmega16M1 датащи(PDF) 37 Page - ATMEL Corporation

ATmega16M1 датащи(HTML) 37 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL