ATmega162 datasheet(171/324 Pages) ATMEL

171 / 324 page

171

2513K–AVR–07/09

ATmega162/V

Frame Formats

A serial frame is defined to be one character of data bits with synchronization bits (start and stop

bits), and optionally a parity bit for error checking. The USART accepts all 30 combinations of

the following as valid frame formats:

•

1 start bit

•

5, 6, 7, 8, or 9 data bits

•

no, even or odd parity bit

•

1 or 2 stop bits

A frame starts with the start bit followed by the least significant data bit. Then the next data bits,

up to a total of nine, are succeeding, ending with the most significant bit. If enabled, the parity bit

is inserted after the data bits, before the stop bits. When a complete frame is transmitted, it can

be directly followed by a new frame, or the communication line can be set to an idle (high) state.

Figure 78 illustrates the possible combinations of the frame formats. Bits inside brackets are

optional.

Figure 78. Frame Formats

Start bit, always low.

(n)

Data bits (0 to 8).

Parity bit. Can be odd or even.

Stop bit, always high.

IDLE

No transfers on the communication line (RxD or TxD). An IDLE line must be

high.

The frame format used by the USART is set by the UCSZ2:0, UPM1:0 and USBS bits in UCSRB

and UCSRC. The Receiver and Transmitter use the same setting. Note that changing the setting

of any of these bits will corrupt all ongoing communication for both the Receiver and Transmitter.

The USART Character SiZe (UCSZ2:0) bits select the number of data bits in the frame. The

USART Parity mode (UPM1:0) bits enable and set the type of parity bit. The selection between

one or two stop bits is done by the USART Stop Bit Select (USBS) bit. The receiver ignores the

second stop bit. An FE (Frame Error) will therefore only be detected in the cases where the first

stop bit is zero.

Parity Bit Calculation

The parity bit is calculated by doing an exclusive-or of all the data bits. If odd parity is used, the

result of the exclusive or is inverted. The relation between the parity bit and data bits is as

follows::

even

Parity bit using even parity

odd

Parity bit using odd parity

Data bit n of the character

If used, the parity bit is located between the last data bit and first stop bit of a serial frame.

[5]

[6]

[7]

[8]

[P]

Sp1 [Sp2]

(St / IDLE)

(IDLE)

FRAME

Peven

dn 1

–

…

Podd

⊕

⊕⊕⊕⊕⊕

dn 1

–

…

⊕

⊕⊕⊕⊕⊕

ATmega162 датащи(PDF) 171 Page - ATMEL Corporation

ATmega162 датащи(HTML) 171 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL