ATmega16 datasheet(183/357 Pages) ATMEL

183 / 357 page

183

2466S–AVR–05/09

ATmega16(L)

• Bit 0 – TWGCE: TWI General Call Recognition Enable Bit

If set, this bit enables the recognition of a General Call given over the Two-wire Serial Bus.

Using the TWI

The AVR TWI is byte-oriented and interrupt based. Interrupts are issued after all bus events, like

reception of a byte or transmission of a START condition. Because the TWI is interrupt-based,

the application software is free to carry on other operations during a TWI byte transfer. Note that

the TWI Interrupt Enable (TWIE) bit in TWCR together with the Global Interrupt Enable bit in

SREG allow the application to decide whether or not assertion of the TWINT Flag should gener-

ate an interrupt request. If the TWIE bit is cleared, the application must poll the TWINT Flag in

order to detect actions on the TWI bus.

When the TWINT Flag is asserted, the TWI has finished an operation and awaits application

response. In this case, the TWI Status Register (TWSR) contains a value indicating the current

state of the TWI bus. The application software can then decide how the TWI should behave in

the next TWI bus cycle by manipulating the TWCR and TWDR Registers.

Figure 85 is a simple example of how the application can interface to the TWI hardware. In this

example, a Master wishes to transmit a single data byte to a Slave. This description is quite

abstract, a more detailed explanation follows later in this section. A simple code example imple-

menting the desired behavior is also presented.

Figure 85. Interfacing the Application to the TWI in a Typical Transmission

The first step in a TWI transmission is to transmit a START condition. This is done by

writing a specific value into TWCR, instructing the TWI hardware to transmit a START

condition. Which value to write is described later on. However, it is important that the

TWINT bit is set in the value written. Writing a one to TWINT clears the flag. The TWI will

not start any operation as long as the TWINT bit in TWCR is set. Immediately after the

application has cleared TWINT, the TWI will initiate transmission of the START condition.

When the START condition has been transmitted, the TWINT Flag in TWCR is set, and

TWSR is updated with a status code indicating that the START condition has success-

fully been sent.

The application software should now examine the value of TWSR, to make sure that the

START condition was successfully transmitted. If TWSR indicates otherwise, the applica-

tion software might take some special action, like calling an error routine. Assuming that

the status code is as expected, the application must load SLA+W into TWDR. Remember

that TWDR is used both for address and data. After TWDR has been loaded with the

START

SLA+W

Data

STOP

1. Application

writes to TWCR to

initiate

transmission of

START

2. TWINT set.

Status code indicates

START condition sent

4. TWINT set.

Status code indicates

SLA+W sent, ACK

received

6. TWINT set.

Status code indicates

data sent, ACK received

3. Check TWSR to see if START was

sent.

Application loads SLA+W into TWDR, and

loads appropriate control signalsinto

TWCR, making sure that TWINT is written

to one, and TWSTA is written to zero

5. Check TWSR to see if SLA+W was

sent and ACK received.

Application loads data into TWDR, and

loads appropriate control signals into

TWCR, making sure that TWINT is

written to one

7. Check TWSR to see if data was sent

and ACK received.

Application loads appropriate control

signals to send STOP into TWCR,

making sure that TWINT is written to one

TWI bus

Indicates

TWINT set

Application

Action

TWI

Hardware

Action

ATmega16 датащи(PDF) 183 Page - ATMEL Corporation

ATmega16 датащи(HTML) 183 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL