MCP73113 datasheet(18/34 Pages) MICROCHIP

18 / 34 page

MCP73113/4

DS22183B-page 18

5.5

Constant Current MODE - Fast

Charge

During the constant current mode, the programmed

charge current is supplied to the battery or load.

The charge current is established using a single

resistor from PROG to VSS. The program resistor and

the charge current are calculated using the following

equation:

EQUATION 5-1:

EQUATION 5-2:

Table 5-1 provides commonly seen E96 (1%) and E24

(5%) resistors for various charge current to reduce

design time.

TABLE 5-1:

RESISTOR LOOKUP TABLE

Constant current mode is maintained until the voltage

at the VBAT pin reaches the regulation voltage, VREG.

When constant current mode is invoked, the internal

timer is reset.

5.5.1

TIMER EXPIRED DURING

CONSTANT CURRENT - FAST

CHARGE MODE

If the internal timer expires before the recharge voltage

threshold is reached, a timer fault is indicated and the

charge cycle terminates. The MCP73113/4 devices

remainsin this condition until the battery is removed. If

the battery is removed or input power is cycled. The

MCP73113/4 device enters the Stand-by mode where

it remains until a battery is reinserted.

5.6

Constant Voltage Mode

When the voltage at the VBAT pin reaches the

regulation voltage, VREG, constant voltage regulation

begins. The regulation voltage is factory set to 4.10V,

4.20V, 4.35V or 4.40V with a tolerance of ± 0.5%.

5.7

Charge Termination

The charge cycle is terminated when, during constant

voltage mode, the average charge current diminishes

below a threshold established with the value of 5%,

7.5%, 10% or 20% of fast charge current or internal

timer has expired. A 1 ms filter time on the termination

comparator ensures that transient load conditions do

not result in premature charge cycle termination. The

timer period is factory set and can be disabled. Refer to

Section 1.0 “Electrical Characteristics” for timer

period options.

5.8

Automatic Recharge

The MCP73113/4 device continuously monitors the

voltage at the VBAT pin in the charge complete mode. If

the voltage drops below the recharge threshold,

another charge cycle begins and current is once again

supplied to the battery or load. The recharge threshold

is factory set. Refer to

Section 1.0 “Electrical

Characteristics” for recharge threshold options.

For the MCP73113/4 devices with no recharge option,

the MCP73113/4 will go into standby mode when

termination condition is met. The charge will not restart

until following condition has met:

• Battery is removed from system and insert again.

•VDD is removed and plug in again

• RPROG is disconnected (or high impedance) and

reconnect

Charge

Current (mA)

Recommended

E96 Resistor (

Ω)

Recommended

E24 Resistor (

Ω)

130

10k

150

8.45k

8.20k

200

6.20k

250

4.99k

5.10k

300

4.02k

3.90k

350

3.40k

3.30k

400

3.00k

450

2.61k

2.70k

500

2.32k

2.37k

550

2.10k

2.20k

600

1.91k

2.00k

650

1.78k

1.80k

700

1.62k

1.60k

750

1.50k

800

1.40k

1.50k

850

1.33k

1.30k

900

1.24k

1.20k

950

1.18k

1.20k

1000

1.10k

1100

1.00k

REG

1104

0.93

–

Where:

RPROG

kilo-ohms (k

Ω)

IREG

milliampere (mA)

PROG

REG

1104

------------

⎝⎠

⎛⎞

log

⎝⎠

⎛⎞

0.93

–

()

⁄

Where:

RPROG

kilo-ohms (k

Ω)

IREG

milliampere (mA)

Note:

The MCP73113/4 also offer options with

no automatic recharge.

MCP73113 датащи(PDF) 18 Page - Microchip Technology

MCP73113 датащи(HTML) 18 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

датащи скачать

ссылки URL