XR16M554 datasheet(21/46 Pages) EXAR

21 / 46 page

XR16M554/554D

REV. 1.0.0

1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO

4.3.1

IER versus Receive FIFO Interrupt Mode Operation

When the receive FIFO (FCR BIT-0 = 1) and receive interrupts (IER BIT-0 = 1) are enabled, the RHR interrupts

(see ISR bits 2 and 3) status will reflect the following:

A. The receive data available interrupts are issued to the host when the FIFO has reached the programmed

trigger level. It will be cleared when the FIFO drops below the programmed trigger level.

B. FIFO level will be reflected in the ISR register when the FIFO trigger level is reached. Both the ISR register

status bit and the interrupt will be cleared when the FIFO drops below the trigger level.

C. The receive data ready bit (LSR BIT-0) is set as soon as a character is transferred from the shift register to

the receive FIFO. It is reset when the FIFO is empty.

4.3.2

IER versus Receive/Transmit FIFO Polled Mode Operation

When FCR BIT-0 equals a logic 1 for FIFO enable; resetting IER bits 0-3 enables the XR16M554 in the FIFO

polled mode of operation. Since the receiver and transmitter have separate bits in the LSR either or both can

be used in the polled mode by selecting respective transmit or receive control bit(s).

A. LSR BIT-0 indicates there is data in RHR or RX FIFO.

B. LSR BIT-1 indicates an overrun error has occurred and that data in the FIFO may not be valid.

C. LSR BIT 2-4 provides the type of receive data errors encountered for the data byte in RHR, if any.

D. LSR BIT-5 indicates THR is empty.

E. LSR BIT-6 indicates when both the transmit FIFO and TSR are empty.

F. LSR BIT-7 indicates a data error in at least one character in the RX FIFO.

IER[0]: RHR Interrupt Enable

The receive data ready interrupt will be issued when RHR has a data character in the non-FIFO mode or when

the receive FIFO has reached the programmed trigger level in the FIFO mode.

• Logic 0 = Disable the receive data ready interrupt (default).

• Logic 1 = Enable the receiver data ready interrupt.

IER[1]: THR Interrupt Enable

This bit enables the Transmit Ready interrupt which is issued whenever the THR becomes empty. If the THR is

empty when this bit is enabled, an interrupt will be generated.

• Logic 0 = Disable Transmit Ready interrupt (default).

• Logic 1 = Enable Transmit Ready interrupt.

IER[2]: Receive Line Status Interrupt Enable

If any of the LSR register bits 1, 2, 3 or 4 is a logic 1, it will generate an interrupt to inform the host controller

about the error status of the current data byte in FIFO. LSR bit-1 generates an interrupt immediately when an

overrun occurs. LSR bits 2-4 generate an interrupt when the character in the RHR has an error.

• Logic 0 = Disable the receiver line status interrupt (default).

• Logic 1 = Enable the receiver line status interrupt.

IER[3]: Modem Status Interrupt Enable

• Logic 0 = Disable the modem status register interrupt (default).

• Logic 1 = Enable the modem status register interrupt.

IER[7:4]: Reserved (Default 0)

XR16M554 датащи(PDF) 21 Page - Exar Corporation

XR16M554 датащи(HTML) 21 Page - Exar Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

датащи скачать

ссылки URL